Translation

English
English French Actions
The ``tcpi_state`` variable used in this script is returned by ``TCP_INFO`` [#ftcpinfo]_. It tracks the state of the TCP connection according to TCP's finite state machine [#fstates]_. This script is available from :download:`/exercises/packetdrill_scripts/client.pkt`.
Another example is the simultaneous establishment of a TCP connection. The TCP stack sends a ``SYN`` and receives a ``SYN`` in response instead of a ``SYN+ACK``. It then acknowledges the received ``SYN`` and retransmits its own ``SYN``. The connection becomes established upon reception of the fourth segment. This script is available from :download:`/exercises/packetdrill_scripts/dual.pkt`.
Another usage of packetdrill_ is to explore how a TCP connection ends. The scripts below show how a TCP stack closes a TCP connection. The first example shows a local host that connects to a remote host and then closes the connection. The remote host acknowledges the ``FIN`` and later closes its direction of data transfer. This script is available from :download:`/exercises/packetdrill_scripts/local-close.pkt`.
As for the establishment of a connection, it is also possible for the two communicating hosts to close the connection at the same time. This is shown in the example below where the remote host sends its own ``FIN`` when acknowledging the first one. This script is available from :download:`/exercises/packetdrill_scripts/local-close2.pkt`.
A third scenario for the termination of a TCP connection is that the remote hosts sends its ``FIN`` first. This script is available from :download:`/exercises/packetdrill_scripts/remote-close.pkt`.
Another very interesting utilization of packetdrill_ is to explore how a TCP stack reacts to acknowledgments that would correspond to lost or reordered segments. For this analysis, we configure a very large initial congestion window to ensure that the connection does not start with a slow-start.
Let us first use packetdrill_ to explore the evolution of the TCP retransmission timeout. The value of this timeout is set based on the measured round-trip-time and its variance. When the retransmission timer expires, TCP doubles the retransmission timer. This exponential backoff mechanism is important to ensure that TCP slowdowns during very severe congestion periods. We use the ``tcpi_rto`` variable from ``TCP_INFO`` to track the evolution of the retransmission timer. This script is available from :download:`/exercises/packetdrill_scripts/rto.pkt`.
We can use a similar code to demonstrate that the TCP stack performs a fast retransmit after having received three duplicate acknowledgments. This script is available from :download:`/exercises/packetdrill_scripts/frr.pkt`.
A TCP stack uses both the fast retransmit technique and retransmission timers. A retransmission timer can fire after a fast retransmit when several segments are lost. The example below shows a loss of two consecutive segments. This script is available from :download:`/exercises/packetdrill_scripts/frr-rto.pkt`.
More complex scenarios can be written. The script below demonstrates how the TCP stack behaves when three segments are lost. This script is available from :download:`/exercises/packetdrill_scripts/frr-rto2.pkt`.
The examples above have demonstrated how TCP retransmits lost segments. However, they did not consider the interactions with the congestion control scheme since the use a large initial congestion window. We now set the initial congestion window to two MSS-sized segments and use the ``tcpi_snd_cwnd`` and ``tcpi_snd_ssthresh`` variables from ``TCP_INFO`` to explore the evolution of the TCP congestion control scheme. Our first script looks at the evolution of the congestion window during a slow-start when there are no losses. This script is available from :download:`/exercises/packetdrill_scripts/slow-start.pkt`.
Some TCP clients use delayed acknowledgments and send a TCP acknowledgment after after second in-sequence segment. This behavior is illustrated in the script below. This script is available from :download:`/exercises/packetdrill_scripts/slow-start-delayed.pkt`.
We can now explore how TCP's retransmission techniques interact with the congestion control scheme. The Linux TCP code that combines these two techniques contains several heuristics to improve their performance. We start with a transfer of 8KBytes where the penultimate segment is not received by the remote host. In this case, TCP does not receive enough acknowledgments to trigger the fast retransmit and it must wait for the expiration of the retransmission timer. This script is available from :download:`/exercises/packetdrill_scripts/slow-start-rto2.pkt`.
Another interesting scenario is when the loss happens early in the data transfer. This is shown in the script below where the second segment is lost. We observe that by triggering transmissions of unacknowledged data, the :rfc:`3042` rule speeds up the recovery since a fast retransmit happens. This script is available from :download:`/exercises/packetdrill_scripts/slow-start-frr2.pkt`.
Our last scenario is when the first segment sent is lost. In this case, two round-trip-times are required to retransmit the missing segment and recover from the loss. This script is available from :download:`/exercises/packetdrill_scripts/slow-start-frr3.pkt`.
Open questions
Unless otherwise noted, we assume for the questions in this section that the following conditions hold.
the sender/receiver performs a single :manpage:`send(3)` of `x` bytes
the round-trip-time is fixed and does not change during the lifetime of the TCP connection. We assume a fixed value of 100 milliseconds for the round-trip-time and a fixed value of 200 milliseconds for the retransmission timer.
the delay required to transmit a single TCP segment containing MSS bytes is small and set to 1 milliseconds, independently of the MSS size
the transmission delay for a TCP acknowledgment is negligible
the initial value of the congestion window is one MSS-sized segment
the value of the duplicate acknowledgment threshold is fixed and set to 3
TCP always acknowledges each received segment
To understand the operation of the TCP congestion control, it is often useful to write time-sequence diagrams for different scenarios. The example below shows the operation of the TCP congestion control scheme in a very simple scenario. The initial congestion window (``cwnd``) is set to 1000 bytes and the receive window (``rwin``) advertised by the receiver (supposed constant for the entire connection) is set to 2000 bytes. The slow-start threshold (``ssthresh``) is set to 64000 bytes.
Can you explain why the sender only sends one segment first and then two successive segments (the delay between the two segments on the figure is due to graphical reasons) ?
Can you explain why the congestion window is increased after the reception of the first acknowledgment ?
How long does it take for the sender to deliver 3 KBytes to the receiver ?
Same question as above but now with a small variation. Recent TCP implementations use a large initial value for the congestion window. Draw the time-sequence diagram that corresponds to an initial value of 10000 bytes for this congestion window.
Same question as the first one, but consider that the MSS on the sender is set to 500 bytes. How does this modification affect the entire delay ?
Assuming that there are no losses and that there is no congestion in the network. If the sender writes `x` bytes on a newly established TCP connection, derive a formula that computes the minimum time required to deliver all these `x` bytes to the receiver. For the derivation of this formula, assume that `x` is a multiple of the maximum segment size and that the receive window and the slow-start threshold are larger than `x`.
Component Translation Difference to current string
This translation Propagated Empty cnp3-ebook/exercises/tcp-2
The following strings have the same context and source.
Propagated Translated cnp3-ebook/exercises/transport Questions ouvertes
Propagated Translated cnp3-ebook/exercises/reliability Questions ouvertes

Loading…

User avatar None

New source string

cnp3-ebook / exercises/tcp-2French

New source string a year ago
Browse all component changes

Things to check

Inconsistent

This string has more than one translation in this project or is untranslated in some components.

Reset

Glossary

English French
No related strings found in the glossary.

String information

Source string location
../../exercises/tcp-2.rst:637
String age
a year ago
Source string age
a year ago
Translation file
locale/fr/LC_MESSAGES/exercises/tcp-2.po, string 43