English French
the `request-response service`
The connectionless service
The `connectionless service` that we have described earlier is frequently used by users who need to exchange small SDUs. It can be easily built on top of the connectionless network layer service that we have described earlier. Users needing to either send or receive several different and potentially large SDUs, or who need structured exchanges often prefer the `connection-oriented service`.
The connection-oriented service
The establishment of a connection can be modeled by using four primitives : `Connect.request`, `Connect.indication`, `Connect.response` and `Connect.confirm`. The `Connect.request` primitive is used to request the establishment of a connection. The main parameter of this primitive is the `address` of the destination user. The service provider delivers a `Connect.indication` primitive to inform the destination user of the connection attempt. If it accepts to establish a connection, it responds with a `Connect.response` primitive. At this point, the connection is considered to be established and the destination user can start sending SDUs over the connection. The service provider processes the `Connect.response` and will deliver a `Connect.confirm` to the user who initiated the connection. The delivery of this primitive terminates the connection establishment phase. At this point, the connection is considered to be open and both users can send SDUs. A successful connection establishment is illustrated below.
The example above shows a successful connection establishment. However, in practice not all connections are successfully established. One reason is that the destination user may not agree, for policy or performance reasons, to establish a connection with the initiating user at this time. In this case, the destination user responds to the `Connect.indication` primitive by a `Disconnect.request` primitive that contains a parameter to indicate why the connection has been refused. The service provider will then deliver a `Disconnect.indication` primitive to inform the initiating user.
A second reason is when the service provider is unable to reach the destination user. This might happen because the destination user is not currently attached to the network or due to congestion. In these cases, the service provider responds to the `Connect.request` with a `Disconnect.indication` primitive whose `reason` parameter contains additional information about the failure of the connection.
Once the connection has been established, the service provider supplies two data streams to the communicating users. The first data stream can be used by the initiating user to send SDUs. The second data stream allows the responding user to send SDUs to the initiating user. The data streams can be organized in different ways. A first organization is the `message-mode` transfer. With the `message-mode` transfer, the service provider guarantees that one and only one `Data.indication` will be delivered to the endpoint of the data stream for each `Data.request` primitive issued by the other endpoint. The `message-mode` transfer is illustrated in the figure below. The main advantage of the `message-transfer` mode is that the recipient receives exactly the SDUs that were sent by the other user. If each SDU contains a command, the receiving user can process each command as soon as it receives a SDU.
Unfortunately, the `message-mode` transfer is not widely used on the Internet. On the Internet, the most popular connection-oriented service transfers SDUs in `stream-mode`. With the `stream-mode`, the service provider supplies a byte stream that links the two communicating users. The sending user sends bytes by using `Data.request` primitives that contain sequences of bytes as SDUs. The service provider delivers SDUs containing consecutive bytes to the receiving user by using `Data.indication` primitives. The service provider ensures that all the bytes sent at one end of the stream are delivered correctly in the same order at the other endpoint. However, the service provider does not attempt to preserve the boundaries of the SDUs. There is no relation enforced by the service provider between the number of `Data.request` and the number of `Data.indication` primitives. The `stream-mode` is illustrated in the figure below. In practice, a consequence of the utilization of the `stream-mode` is that if the users want to exchange structured SDUs, they will need to provide the mechanisms that allow the receiving user to separate successive SDUs in the byte stream that it receives. Application layer protocols often use specific delimiters such as the end of line character to delineate SDUs in a bytestream.
An abrupt connection release can also be triggered by one of the users. If a user needs, for any reason, to terminate a connection quickly, it can issue a `Disconnect.request` primitive and to request an abrupt release. The service provider will process the request, stop the two data streams and deliver the `Disconnect.indication` primitive to the remote user as soon as possible. As illustrated in the figure below, this abrupt connection release may cause losses of SDUs.
To ensure a reliable delivery of the SDUs sent by each user over a connection, we need to consider the two streams that compose a connection as independent. A user should be able to release the stream that it uses to send SDUs once it has sent all the SDUs that it planned to send over this connection, but still continue to receive SDUs over the opposite stream. This `graceful` connection release is usually performed as shown in the figure below. One user issues a `Disconnect.request` primitive to its provider once it has issued all its `Data.request` primitives. The service provider will wait until all `Data.indication` primitives have been delivered to the receiving user before issuing the `Disconnnect.indication` primitive. This primitive informs the receiving user that it will no longer receive SDUs over this connection, but it is still able to issue `Data.request` primitives on the stream in the opposite direction. Once the user has issued all of its `Data.request` primitives, it issues a `Disconnnect.request` primitive to request the termination of the remaining stream. The service provider will process the request and deliver the corresponding `Disconnect.indication` to the other user once it has delivered all the pending `Data.indication` primitives. At this point, all data has been delivered, the two streams have been released successfully and the connection is completely closed.
Reliability of the connection-oriented service
The request-response service
The `request-response service` is a compromise between the `connectionless service` and the `connection-oriented service`. Many applications need to send a small amount of data and receive a small amount of information back. This is similar to procedure calls in programming languages. A call to a procedure takes a few arguments and returns a simple answer. In a network, it is sometimes useful to execute a procedure on a different host and receive the result of the computation. Executing a procedure on another host is often called Remote Procedure Call. It is possible to use the `connectionless service` for this application. However, since this service is usually unreliable, this would force the application to deal with any type of error that could occur. Using the `connection oriented service` is another alternative. This service ensures the reliable delivery of the data, but a connection must be created before the beginning of the data transfer. This overhead can be important for applications that only exchange a small amount of data.
The `request-response service` allows to efficiently exchange small amounts of information in a request and associate it with the corresponding response. This service can be depicted by using the time-sequence diagram below.
Services and layers
In the previous sections, we have described services that are provided by the transport layer. However, it is important to note that the notion of service is more general than in the transport layer. As explained earlier, the network layer also provides a service, which in most networks is an unreliable connectionless service. There are network layers that provide a connection-oriented service. Similarly, the datalink layer also provides services. Some datalink layers will provide a connectionless service. This will be the case in Local Area Networks for examples. Other datalink layers, e.g. in public networks, provide a connection oriented service.
To deal with these issues, the transport layer includes several mechanisms that depend on the service that it provides. It interacts with both the applications and the underlying network layer.
Interactions between the transport layer, its user, and its network layer provider
We have already described in the datalink layers mechanisms to deal with data losses and transmission errors. These techniques are also used in the transport layer.