cnp3-ebook/exercises/routing-policies — French @ Weblate: An ICMPv6 error message includes in its message body the …

Zen

Translation

English

French

Needs editing

Skip

	English	French	Actions
	In this internet, some ASes cannot reach all other ASes. Can you fix the problem by adding one shared-cost peering link or one customer-provider peering link ?
	Consider the network below in which a stub domain, `AS456`, is connected to two providers `AS123` and `AS789`. `AS456` advertises its prefix to both its providers. On the other hand, `AS123` advertises ``2001:db8:dead::/48`` while `AS789` advertises ``2001:db8:beef::/48`` and ``2001:db8:dead:cafe::/63``. Via which provider will the packets destined to ``2001:db8:dead:cafe::1`` will be received by `AS456` ?
	Should `AS123` change its configuration ?
	Consider that the AS stub (`AS456`) shown in the figure below decides to advertise two ``/48`` prefixes instead of its allocated ``/47`` prefix.
	Via which provider does `AS456` receive the packets destined to ``2001:db8:caff::bb`` and ``2001:db8:cafe::aa`` ?
	How is the reachability of these addresses affected when link `R1`-`R3` fails ?
	Propose a configuration on R1 that achieves the same objective as the one shown in the figure but also preserves the reachability of all IP addresses inside `AS456` if one of `AS456`'s interdomain links fails.
	Consider the network shown below. In this network, the metric of each link is set to `1` except link `A-B` whose metric is set to `4` in both directions. In this network, there are two paths with the same cost between `D` and `C`. Old routers would randomly select one of these equal cost paths and install it in their forwarding table. Recent routers are able to use up to `N` equal cost paths towards the same destination.
	A simple network
	On recent routers, a lookup in the forwarding table for a destination address returns a set of outgoing interfaces. How would you design an algorithm that selects the outgoing interface used for each packet, knowing that to avoid reordering, all segments of a given TCP connection should follow the same path ?
	A ``traceroute6`` towards ``ipv6.google.com`` provides the following output :
	Can you explain why at the eighth, ninth and tenth hopes several IPv6 addresses are reported in the ``traceroute6`` output ?
	`Section 3.3 <https://tools.ietf.org/html/rfc4443#section-3.3>`_ of :rfc:`4443` explains two different reasons why an IPv6 enabled device could generate an ICMPv6 Time Exceeded message. Explain when a router could generate such a message with ``Code==0`` and when a host could generate such a message with ``Code==1``.
	`Section 3.1 <https://tools.ietf.org/html/rfc4443#section-3.1>`_ of :rfc:`4443` seven different Codes for the ICMPv6 Destination Unreachable Message. Under which circumstances would a router generate such an ICMPv6 message with :
	``Code==0``
	An ICMPv6 error message includes in its message body the beginning of the IPv6 packet that triggered this error. How many bytes of the original packet must be returned to allow the host to recover the original source and destination addresses and source and destination ports of the packet that caused the error ?

Loading…

None

Source string added

English 0 characters edited

4 years ago

Browse all string changes

Glossary

English	French
No related strings found in the glossary.

30491 String information

Source string location

../../exercises/routing-policies.rst:213

String age

4 years ago

Last updated

2 months ago

Source string age

4 years ago

Translation file

locale/fr/LC_MESSAGES/exercises/routing-policies.po, string 25

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.