cnp3-ebook/exercises/routing-protocols — English @ Weblate: OSPFv3 also includes `LS Acknowledge` packets that acknowledge the correct …

The translation has come to an end.

Zen

Source string Source string

English

OSPFv3 also includes `LS Acknowledge` packets that acknowledge the correct reception of link state information.

The string is read-only.

Skip

	English	Actions
	We use this mininet_ topology to collect packet traces that show the packets that OSPF routers exchange. For this, we add the following ``post_build`` method that IPMininet_ starts after having constructed the network and before launching the daemons. It simply starts tcpdump_ on each router to collect the first 100 OSPF packets that they send/receive.
	Finally, we can start the IPMininet_ topology and launch the daemons. The entire script is available from :download:`/exercises/ipmininet_scripts/ospf6.py`.
	The script starts the routers and hosts.
	We can easily verify that the paths used to forward packets are the expected ones according to the configured IGP weights.
	We can also connect to the OSPFv3 daemon running on the routers to observe its state. For this, we use the ``noecho r1 telnet localhost ospf6d`` command.
	The password to access this daemon is `zebra`. It supports various commands that are described in the `FRRouting documentation <http://docs.frrouting.org/en/latest/ospf6d.html#showing-ospf6-information>`_ We briefly illustrate some of them below.
	The ``show ipv6 ospf6`` command reports the general state of the OSPFv3 daemon. The ``show ipv6 ospf6 neighbor`` command reports the state of the connected neighbors.
	In its output, we see that ``r1`` is attached to two different routers. Finally, the ``show ipv6 ospf6 database`` returns the full OSPFv3 database with all the link state information that was distributed by OSPFv3.
	We can also use the packet traces that were collected by tcpdump_ to observe the packets that the OSPFv3 daemons exchange. OSPFv3 is a more complex protocol that the basic link state protocol that we have described in this book, but you should be able to understand some of these packets. The packet traces are available as :download:`/exercises/traces/ospf6-r1-trace.pcap`, :download:`/exercises/traces/ospf6-r2-trace.pcap` and :download:`/exercises/traces/ospf6-r3-trace.pcap`. Here are a few interesting packets collected on router ``r1``.
	The first packet that this router received his a Hello packet that was sent by router ``r2``. There are several interesting points to note about this packet. First, its source address is the link-local address (``fe80::68bc:b4ff:fe19:42b7``) of router ``r2`` on this interface. The destination address of the packet is reserved IPv6 multicast address for OSPFv3, i.e. ``ff02::5``. The Hop Limit of the packet is set to 1 and OSFPv3 uses a next header of type 89.
	The Hello packet contains some parameters such as the `Hello interval` that is set to 1 second. This interval is the delay between the transmission of successive Hello packets. Since the `Router Dead Interval` is set to 3 seconds, the router will consider the link as down if it does not receive Hello packets during a period of 3 seconds. The second packet of the trace is sent by router ``r1``.
	We can then observe the Database description packet that is sent by routers to announce the state of their OSPFv3 database. The details of this packet are beyond the scope of this simple exercise.
	This packet is updated when new information is added in the router's OSPFv3 database. A few seconds router, this router sends another Database description packet that announces more information.
	Router ``r2`` reacts to this updated Database description packet by requesting the link state information that it does not already know. For this, it sends a `LS Request` packet.
	The requested information is sent in a `LS Update` packet shortly after that.
	OSPFv3 also includes `LS Acknowledge` packets that acknowledge the correct reception of link state information.
	A more detailed discussion of the packets that routing protocols exchange may be found in [Goralski2009]_.
	Exploring RIP
	IPMininet_ can also be used to perform experiments with RIP. A simple script that uses RIPng is provided below.
	As RIP messages are exchanged using UDP on port 521, we filter this port in the tcpdump_ trace. RIPng distributes the routes and our two hosts can exchange packets. The entire script is available from :download:`/exercises/ipmininet_scripts/ripng.py`.
	We can observe the RIPng messages that are exchanged over the network. :rfc:`2080` defines two types of RIPng messages:
	the requests
	the responses that contain the router's routing table
	When a router starts, it sends a request message. This is illustrated in the figure below with the first message sent by router ``r2``. This message is sent inside an IPv6 packet whose source address is the link-local address of the router and the destination address is ``ff02::9`` which is the reserved multicast address for RIPng.
	Router ``r2`` receives a similar request from ``fe80::481a:48ff:fed7:292e`` and replies by sending its routing table in a response message. Note that this message is sent to the link-local address of the requesting router.
	Later, router ``r2`` will regularly transmit its distance vector inside an unsolicited response message that is sent towards the IPv6 multicast address ``ff02::9``.
	The packet traces collected on the three routers of this example are available from :download:`/exercises/traces/ripng-r1-trace.pcap`, :download:`/exercises/traces/ripng-r2-trace.pcap` and :download:`/exercises/traces/ripng-r3-trace.pcap`.
	Exploring BGP
	To explore the configuration of BGP, let us consider a network that contains three ASes: ``AS1``, ``AS2`` and ``AS3``. To simplify the tests, we identify one host inside each of these ASes.
	As in the previous examples, we create the routers and associate one IPv6 prefix to each AS:
	``AS1`` is assigned ``2001:cafe:1::/48``

Loading…

gegoa

String updated in the repository

English

English 0 characters edited Current translation State: Read-only

4 months ago

Browse all string changes

Glossary

English	English
No related strings found in the glossary.

35602 String information

Flags

read-only, rst-text

Source string location

../../exercises/routing-protocols.rst:265

String age

4 years ago

Last updated

4 months ago

Source string age

4 years ago

Translation file

locale/pot/exercises/routing-protocols.pot, string 21

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.