cnp3-ebook/exercises/transport — Czech @ Weblate: Continue the connection so that `Host B` sends `Hello` as …

Translation

English

Czech

Needs editing

Skip

	English	Czech	Actions
	Serving applications
	This is an unpolished draft of the third edition of this e-book. If you find any error or have suggestions to improve the text, please create an issue via https://github.com/CNP3/ebook/issues?milestone=3 or help us by providing pull requests to close the existing issues.
	Open questions
	A reliable connection oriented transport places a 32 bits sequence number inside the segment header to number the segments. This sequence number is incremented for each data segment. The connection starts as shown in the figure below :
	Continue the connection so that `Host B` sends `Hello` as data and `Host A` replies by sending `Pleased to meet you`. After having received the response, `Host B` closes the connection gracefully and `Host A` does the same. Discuss on the state that needs to be maintained inside each host.
	A transport connection that provides a message-mode service has been active for some time and all data has been exchanged and acknowledged in both directions. As in the exercise above, the sequence number is incremented after the transmission of each segment. At this time, `Host A` sends two DATA segments as shown in the figure below.
	What are the acknowledgments sent by `Host B`. How does `Host A` react and how does it terminate the connection ?
	Consider a reliable connection-oriented transport protocol that provides the bytestream service. In this transport protocol, the sequence number that is placed inside each DATA segment reflects the position of the bytes in the bytestream. Considering the connection shown below, provide the DATA segments that are sent by `Host A` in response to the `DATA.request`, assuming that one segment is sent for each `DATA.request`.
	Same question as above, but consider now that the transport protocol tries to send large DATA segments whenever possible. For this exercise, we consider that a DATA segment can contain up to 8 bytes of data in the payload. Do not forget to show the acknowledgments in your answer.
	Consider a transport protocol that provides a reliable connection-oriented bytestream service. You observe the segments sent by a host that uses this protocol. Does the time-sequence diagram below reflects a valid implementation of this protocol ? Justify your answer.
	In the above example, the two `DATA` segments were lost before arriving at the destination. Discuss the following scenario and explain how the receiver should react to the reception of the last `DATA` segment.
	A network layer service guarantees that a packet will never live during more than 100 seconds inside the network. Consider a reliable connection-oriented transport protocol that places a 32 bits sequence number inside each segment. What is the maximum rate (in segments per second) at which is should sent data segments to prevent having two segments with the same sequence number inside the network ?
	Practice
	Amazon provides the `S3 storage service <https://s3.amazonaws.com/>`_ where companies and researchers can store lots of information and perform computations on the stored information. Amazon allows users to send files through the Internet, but also by sending hard-disks. Assume that a 1 Terabyte hard-disk can be delivered within 24 hours to Amazon by courier service. What is the minimum bandwidth required to match the bandwidth of this courier service ?
	Discussion questions
	In the transport layer, the receive window advertised by a receiver can vary during the lifetime of the connection. What are the causes for these variations ?
	A reliable connection-oriented protocol can provide a message-mode service or a byte stream service. Which of the following usages of the sequence numbers is the best suited for each of these services ?
	DATA segments contain a sequence number that is incremented for each byte transmitted
	DATA segments contain a sequence number that is incremented for each DATA segment transmitted
	Some transport protocols use 32 bits sequence numbers while others use 64 bits sequence number. What are the advantages and drawbacks of each approach ?

Loading…

None

Source string added

English 0 characters edited

6 years ago

Browse all string changes

Glossary

English	Czech
No related strings found in the glossary.

17234 String information

Source string location

../../exercises/transport.rst:38

String age

6 years ago

Last updated

2 months ago

Source string age

6 years ago

Translation file

locale/cs/LC_MESSAGES/exercises/transport.po, string 6

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.