cnp3-ebook/principles/network — Czech @ Weblate: Consider now that the link between `D` and `E` fails. …

Zen

Translation

English

Czech

Needs editing

Skip

	English	Czech	Actions
	`C` sends its distance vector `[C=0]` to `B` and `E`
	`E` sends its distance vector `[E=0,D=1,A=2,C=1]` to `D`, `B` and `C`. `B` can now reach `A`, `C`, `D` and `E`
	`B` sends its distance vector `[B=0,A=1,C=1,D=2,E=1]` to `A`, `C` and `E`. `A`, `B`, `C` and `E` can now reach all five routers of this network.
	`A` sends its distance vector `[A=0,B=1,C=2,D=1,E=2]` to `B` and `D`.
	At this point, all routers can reach all other routers in the network thanks to the routing tables shown in the figure below.
	To deal with link and router failures, routers use the timestamp stored in their routing table. As all routers send their distance vector every `N` seconds, the timestamp of each route should be regularly refreshed. Thus no route should have a timestamp older than `N` seconds, unless the route is not reachable anymore. In practice, to cope with the possible loss of a distance vector due to transmission errors, routers check the timestamp of the routes stored in their routing table every `N` seconds and remove the routes that are older than :math:`3 \times N` seconds.
	When a router notices that a route towards a destination has expired, it must first associate an :math:`\infty` cost to this route and send its distance vector to its neighbors to inform them. The route can then be removed from the routing table after some time (e.g. :math:`3 \times N` seconds), to ensure that the neighboring routers have received the bad news, even if some distance vectors do not reach them due to transmission errors.
	Consider the example above and assume that the link between routers `A` and `B` fails. Before the failure, `A` used `B` to reach destinations `B`, `C` and `E` while `B` only used the `A-B` link to reach `A`. The two routers detect the failure by the timeouts in the affected entries in their routing tables. Both routers `A` and `B` send their distance vector.
	`A` sends its distance vector :math:`[A=0,B=\infty,C=\infty,D=1,E=\infty]`. `D` knows that it cannot reach `B` anymore via `A`
	`D` sends its distance vector :math:`[D=0,B=\infty,A=1,C=2,E=1]` to `A` and `E`. `A` recovers routes towards `C` and `E` via `D`.
	`B` sends its distance vector :math:`[B=0,A=\infty,C=1,D=2,E=1]` to `E` and `C`. `C` learns that there is no route anymore to reach `A` via `B`.
	`E` sends its distance vector :math:`[E=0,A=2,C=1,D=1,B=1]` to `D`, `B` and `C`. `D` learns a route towards `B`. `C` and `B` learn a route towards `A`.
	Consider now that the link between `D` and `E` fails. The network is now partitioned into two disjoint parts: (`A` , `D`) and (`B`, `E`, `C`). The routes towards `B`, `C` and `E` expire first on router `D`. At this time, router `D` updates its routing table.
	If `D` sends :math:`[D=0, A=1, B=\infty, C=\infty, E=\infty]`, `A` learns that `B`, `C` and `E` are unreachable and updates its routing table.
	Unfortunately, if the distance vector sent to `A` is lost or if `A` sends its own distance vector ( :math:`[A=0,D=1,B=3,C=3,E=2]` ) at the same time as `D` sends its distance vector, `D` updates its routing table to use the shorter routes advertised by `A` towards `B`, `C` and `E`. After some time `D` sends a new distance vector : :math:`[D=0,A=1,E=3,C=4,B=4]`. `A` updates its routing table and after some time sends its own distance vector :math:`[A=0,D=1,B=5,C=5,E=4]`, etc. This problem is known as the `count to infinity problem` in the networking literature.
	Routers `A` and `D` exchange distance vectors with increasing costs until these costs reach :math:`\infty`. This problem may occur in other scenarios than the one depicted in the above figure. In fact, distance vector routing may suffer from count to infinity problems as soon as there is a cycle in the network. Unfortunately, cycles are widely used in networks since they provide the required redundancy to deal with link and router failures. To mitigate the impact of counting to infinity, some distance vector protocols consider that :math:`16=\infty`. Unfortunately, this limits the metrics that network operators can use and the diameter of the networks using distance vectors.
	This count to infinity problem occurs because router `A` advertises to router `D` a route that it has learned via router `D`. A possible solution to avoid this problem could be to change how a router creates its distance vector. Instead of computing one distance vector and sending it to all its neighbors, a router could create a distance vector that is specific to each neighbor and only contains the routes that have not been learned via this neighbor. This could be implemented by the following pseudocode.
	This technique is called `split-horizon`. With this technique, the count to infinity problem would not have happened in the above scenario, as router `A` would have advertised :math:`[A=0]` after the failure, since it learned all its other routes via router `D`. Another variant called `split-horizon with poison reverse` is also possible. Routers using this variant advertise a cost of :math:`\infty` for the destinations that they reach via the router to which they send the distance vector. This can be implemented by using the pseudo-code below.
	After having detected the failure, router `B` sends its distance vectors:
	:math:`[A=\infty,B=0,C=\infty,E=1]` to router `C`
	:math:`[A=\infty,B=0,C=1,E=\infty]` to router `E`
	If, unfortunately, the distance vector sent to router `C` is lost due to a transmission error or because router `C` is overloaded, a new count to infinity problem can occur. If router `C` sends its distance vector :math:`[A=2,B=1,C=0,E=\infty]` to router `E`, this router installs a route of distance `3` to reach `A` via `C`. Router `E` sends its distance vectors :math:`[A=3,B=\infty,C=1,E=1]` to router `B` and :math:`[A=\infty,B=1,C=\infty,E=0]` to router `C`. This distance vector allows `B` to recover a route of distance `4` to reach `A`.
	Forwarding tables versus routing tables
	Routers usually maintain at least two data structures that contain information about the reachable destinations. The first data structure is the `routing table`. The `routing table` is a data structure that associates a destination to an outgoing interface or a nexthop router and a set of additional attributes. Different routing protocols can associate different attributes for each destination. Distance vector routing protocols will store the cost to reach the destination along the shortest path. Other routing protocols may store information about the number of hops of the best path, its lifetime or the number of sub paths. A `routing table` may store different paths towards a given destination and flag one of them as the best one.
	The `routing table` is a software data structure which is updated by (one or more) routing protocols. The `routing table` is usually not directly used when forwarding packets. Packet forwarding relies on a more compact data structure which is the `forwarding table`. On high-end routers, the `forwarding table` is implemented directly in hardware while lower performance routers will use a software implementation. A `forwarding table` contains a subset of the information found in the `routing table`. It only contains the nexthops towards each destination that are used to forward packets and no attributes. A `forwarding table` will typically associate each destination to one or more outgoing interface or nexthop router.
	Link state routing

Loading…

None

Source string added

English 0 characters edited

6 years ago

Browse all string changes

Glossary

English	Czech
No related strings found in the glossary.

17993 String information

Source string location

../../principles/dv.rst:113

String age

6 years ago

Last updated

2 months ago

Source string age

6 years ago

Translation file

locale/cs/LC_MESSAGES/principles/network.po, string 151

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.