cnp3-ebook/principles/network — Czech @ Weblate: Distance vector routing is a simple distributed routing protocol. Distance …

The translation has come to an end.

Zen

Translation

English

Distance vector routing is a simple distributed routing protocol. Distance vector routing allows routers to automatically discover the destinations reachable inside the network as well as the shortest path to reach each of these destinations. The shortest path is computed based on `metrics` or `costs` that are associated to each link. We use `l.cost` to represent the metric that has been configured for link `l` on a router.

Czech

Needs editing

Skip

	English	Czech	Actions
	->R5
	Since a packet received with `label=1` must be forwarded to `R5` with `label=1`, `R2`'s `label forwarding table` could contain :
	Two virtual circuits pass through `R3`. They both need to be forwarded to `R4`, but `R4` expects `label=1` for packets belonging to the virtual circuit originated by `R2` and `label=0` for packets belonging to the other virtual circuit. `R3` could choose to leave the labels unchanged.
	->R4
	->R3
	The figure below shows the path followed by the packets on the `R1->R3->R4->R2->R5` path in red with on each arrow the label used in the packets.
	MultiProtocol Label Switching (MPLS) is the example of a deployed networking technology that relies on label switching. MPLS is more complex than the above description because it has been designed to be easily integrated with datagram technologies. However, the principles remain. `Asynchronous Transfer Mode` (ATM) and Frame Relay are other examples of technologies that rely on `label switching`.
	Footnotes
	We will see later a more detailed description of Multiprotocol Label Switching, a networking technology that is capable of using one or more labels.
	The control plane
	One of the objectives of the `control plane` in the network layer is to maintain the routing tables that are used on all routers. As indicated earlier, a routing table is a data structure that contains, for each destination address (or block of addresses) known by the router, the outgoing interface over which the router must forward a packet destined to this address. The routing table may also contain additional information such as the address of the next router on the path towards the destination or an estimation of the cost of this path.
	In this section, we discuss the main techniques that can be used to maintain the forwarding tables in a network.
	Distance vector routing
	Distance vector routing is a simple distributed routing protocol. Distance vector routing allows routers to automatically discover the destinations reachable inside the network as well as the shortest path to reach each of these destinations. The shortest path is computed based on `metrics` or `costs` that are associated to each link. We use `l.cost` to represent the metric that has been configured for link `l` on a router.
	Each router maintains a routing table. The routing table `R` can be modeled as a data structure that stores, for each known destination address `d`, the following attributes :
	`R[d].link` is the outgoing link that the router uses to forward packets towards destination `d`
	`R[d].cost` is the sum of the metrics of the links that compose the shortest path to reach destination `d`
	`R[d].time` is the timestamp of the last distance vector containing destination `d`
	A router that uses distance vector routing regularly sends its distance vector over all its interfaces. This distance vector is a summary of the router's routing table that indicates the distance towards each known destination. This distance vector can be computed from the routing table by using the pseudo-code below.
	When a router boots, it does not know any destination in the network and its routing table only contains its local address(es). It thus sends to all its neighbors a distance vector that contains only its address at a distance of `0`. When a router receives a distance vector on link `l`, it processes it as follows.
	The router iterates over all addresses included in the distance vector. If the distance vector contains a destination address that the router does not know, it inserts it inside its routing table via link `l` and at a distance which is the sum between the distance indicated in the distance vector and the cost associated to link `l`. If the destination was already known by the router, it only updates the corresponding entry in its routing table if either :
	The first condition ensures that the router discovers the shortest path towards each destination. The second condition is used to take into account the changes of routes that may occur after a link failure or a change of the metric associated to a link.
	To understand the operation of a distance vector protocol, let us consider the network of five routers shown below.
	Assume that router `A` is the first to send its distance vector `[A=0]`.
	`B` and `D` process the received distance vector and update their routing table with a route towards `A`.
	`D` sends its distance vector `[D=0,A=1]` to `A` and `E`. `E` can now reach `A` and `D`.

Loading…

None

Source string added

English 0 characters edited

6 years ago

Browse all string changes

Glossary

English	Czech
No related strings found in the glossary.

17901 String information

Source string location

../../principles/dv.rst:9

String age

6 years ago

Last updated

2 months ago

Source string age

6 years ago

Translation file

locale/cs/LC_MESSAGES/principles/network.po, string 120

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.