Source string Source string

33/10000 · 33
English Actions
Router `R1` fragments the packet into two fragments before transmitting them to router `R2`. Router `R2` reassembles the two packet fragments in a larger packet before transmitting them on the link towards host `B`.
Each of the packet fragments is a valid packet that contains a header with the source (host `A`) and destination (host `B`) addresses. When router `R2` receives a packet fragment, it treats this packet as a regular packet and forwards it to its final destination (host `B`). Host `B` reassembles the received fragments.
These three solutions have advantages and drawbacks. With the first solution, routers remain simple and do not need to perform any fragmentation operation. This is important when routers are implemented mainly in hardware. However, hosts must be complex since they need to store the packets that they produce if they need to pass through a link that does not support large packets. This increases the buffering required on the hosts.
Furthermore, a single large packet may potentially need to be retransmitted several times. Consider for example a network similar to the one shown above but with four routers. Assume that the link `R1->R2` supports 1000 bytes packets, link `R2->R3` 800 bytes packets and link `R3->R4` 600 bytes packets. A host attached to `R1` that sends large packet will have to first try 1000 bytes, then 800 bytes and finally 600 bytes. Fortunately, this scenario does not occur very often in practice and this is the reason why this solution is used in real networks.
Fragmenting packets on a per-link basis, as presented for the second solution, can minimize the transmission overhead since a packet is only fragmented on the links where fragmentation is required. Large packets can continue to be used downstream of a link that only accepts small packets. However, this reduction of the overhead comes with two drawbacks. First, fragmenting packets, potentially on all links, increases the processing time and the buffer requirements on the routers. Second, this solution leads to a longer end-to-end delay since the downstream router has to reassemble all the packet fragments before forwarding the packet.
The last solution is a compromise between the two others. Routers need to perform fragmentation but they do not need to reassemble packet fragments. Only the hosts need to have buffers to reassemble the received fragments. This solution has a lower end-to-end delay and requires fewer processing time and memory on the routers.
The first solution to the fragmentation problem presented above suggests the utilization of control packets to inform the source about the reception of a too long packet. This is only one of the functions that are performed by the control protocol in the network layer. Other functions include :
sending a control packet back to the source if a packet is received by a router that does not have a valid entry in its forwarding table
sending a control packet back to the source if a router detects that a packet is looping inside the network
verifying that packets can reach a given destination
We will discuss these functions in more details when we will describe the protocols that are used in the network layer of the TCP/IP protocol suite.
Virtual circuit organization
The second organization of the network layer, called `virtual circuits`, has been inspired by the organization of telephone networks. Telephone networks have been designed to carry phone calls that usually last a few minutes. Each phone is identified by a telephone number and is attached to a telephone switch. To initiate a phone call, a telephone first needs to send the destination's phone number to its local switch. The switch cooperates with the other switches in the network to create a bi-directional channel between the two telephones through the network. This channel will be used by the two telephones during the lifetime of the call and will be released at the end of the call. Until the 1960s, most of these channels were created manually, by telephone operators, upon request of the caller. Today's telephone networks use automated switches and allow several channels to be carried over the same physical link, but the principles roughly remain the same.
In a network using virtual circuits, all hosts are also identified with a network layer address. However, packet forwarding is not performed by looking at the destination address of each packet. With the `virtual circuit` organization, each data packet contains one label [#flabels]_. A label is an integer which is part of the packet header. Routers implement `label switching` to forward `labelled data packet`. Upon reception of a packet, a router consults its `label forwarding table` to find the outgoing interface for this packet. In contrast with the datagram mode, this lookup is very simple. The `label forwarding table` is an array stored in memory and the label of the incoming packet is the index to access this array. This implies that the lookup operation has an `O(1)` complexity in contrast with other packet forwarding techniques. To ensure that on each node the packet label is an index in the `label forwarding table`, each router that forwards a packet replaces the label of the forwarded packet with the label found in the `label forwarding table`. Each entry of the `label forwarding table` contains two pieces of information :
the outgoing interface for the packet
the label for the outgoing packet
For example, consider the `label forwarding table` of a network node below.
index
outgoing interface
label
0
South
7
1
none
2
West
3
East
If this node receives a packet with `label=2`, it forwards the packet on its `West` interface and sets the `label` of the outgoing packet to `2`. If the received packet's `label` is set to `3`, then the packet is forwarded over the `East` interface and the `label` of the outgoing packet is set to `2`. If a packet is received with a label field set to `1`, the packet is discarded since the corresponding `label forwarding table` entry is invalid.
`Label switching` enables a full control over the path followed by packets inside the network. Consider the network below and assume that we want to use two virtual circuits : `R1->R3->R4->R2->R5` and `R2->R1->R3->R4->R5`.

Loading…

No matching activity found.
Browse all component changes

Glossary

English English
No related strings found in the glossary.

String information

Flags
read-only
Source string location
../../principles/network.rst:451
String age
5 years ago
Source string age
5 years ago
Translation file
locale/pot/principles/network.pot, string 86