Source string Source string

42/10000 · 42
English Actions
The Datalink layer
The `Datalink layer` builds on the service provided by the underlying physical layer. The `Datalink layer` allows two hosts that are directly connected through the physical layer to exchange information. The unit of information exchanged between two entities in the `Datalink layer` is a frame. A frame is a finite sequence of bits. Some `Datalink layers` use variable-length frames while others only use fixed-length frames. Some `Datalink layers` provide a connection-oriented service while others provide a connectionless service. Some `Datalink layers` provide reliable delivery while others do not guarantee the correct delivery of the information.
An important point to note about the `Datalink layer` is that although the figure below indicates that two entities of the `Datalink layer` exchange frames directly, in reality this is slightly different. When the `Datalink layer` entity on the left needs to transmit a frame, it issues as many `Data.request` primitives to the underlying `physical layer` as there are bits in the frame. The physical layer will then convert the sequence of bits in an electromagnetic or optical signal that will be sent over the physical medium. The `physical layer` on the right hand side of the figure will decode the received signal, recover the bits and issue the corresponding `Data.indication` primitives to its `Datalink layer` entity. If there are no transmission errors, this entity will receive the frame sent earlier.
The Network layer
The `Datalink layer` allows directly connected hosts to exchange information, but it is often necessary to exchange information between hosts that are not attached to the same physical medium. This is the task of the `network layer`. The `network layer` is built above the `datalink layer`. Network layer entities exchange `packets`. A `packet` is a finite sequence of bytes that is transported by the datalink layer inside one or more frames. A packet usually contains information about its origin and its destination, and usually passes through several intermediate devices called routers on its way from its origin to its destination.
The Transport layer
The network layer enables hosts to reach each others. However, different communication flows can take place between the same hosts. These communication flows might have different needs (some require reliable delivery, other not) and need to be distinguished. Ensuring an identification of a communication flow between two given hosts is the task of the `transport layer`. `Transport layer` entities exchange `segments`. A segment is a finite sequence of bytes that are transported inside one or more packets. A transport layer entity issues segments (or sometimes part of segments) as `Data.request` to the underlying network layer entity.
There are different types of transport layers. The most widely used transport layers on the Internet are :term:`TCP`, that provides a reliable connection-oriented bytestream transport service, and :term:`UDP`, that provides an unreliable connection-less transport service.
The Application layer
The upper layer of our architecture is the `Application layer`. This layer includes all the mechanisms and data structures that are necessary for the applications. We will use Application Data Unit (ADU) or the generic Service Data Unit (SDU) term to indicate the data exchanged between two entities of the Application layer.
In the remaining chapters of this text, we will often refer to the information exchanged between entities located in different layers. To avoid any confusion, we will stick to the terminology defined earlier, i.e. :
physical layer entities exchange bits
datalink layer entities exchange *frames*
network layer entities exchange *packets*
transport layer entities exchange *segments*
application layer entities exchange *SDUs*
Reference models
Two reference models have been successful in the networking community : the OSI reference model and the TCP/IP reference model. We discuss them briefly in this section.
The TCP/IP reference model
In contrast with OSI, the TCP/IP community did not spend a lot of effort defining a detailed reference model; in fact, the goals of the Internet architecture were only documented after TCP/IP had been deployed [Clark88]_. :rfc:`1122`, which defines the requirements for Internet hosts, mentions four different layers. Starting from the top, these are :
the Application layer
the Transport layer
the Internet layer which is equivalent to the network layer of our reference model
the Link layer which combines the functions of the physical and datalink layers of our five-layer reference model
Besides this difference in the lower layers, the TCP/IP reference model is very close to the five layers that we use throughout this document.
The OSI reference model
Compared to the five layers reference model explained above, the :term:`OSI` reference model defined in [X200]_ is divided in seven layers. The four lower layers are similar to the four lower layers described above. The OSI reference model refined the application layer by dividing it in three layers :
the `Session layer`. The Session layer contains the protocols and mechanisms that are necessary to organize and to synchronize the dialogue and to manage the data exchange of presentation layer entities. While one of the main functions of the transport layer is to cope with the unreliability of the network layer, the session's layer objective is to hide the possible failures of transport-level connections to the upper layer higher. For this, the Session Layer provides services that allow establishing a session-connection, to support in-order data exchange (including mechanisms that allow recovering from the abrupt release of an underlying transport connection), and to release the connection in an orderly manner.
the `Presentation layer` was designed to cope with the different ways of representing information on computers. There are many differences in the way computer store information. Some computers store integers as 32 bits field, others use 64 bits field and the same problem arises with floating point number. For textual information, this is even more complex with the many different character codes that have been used [#funicode]_. The situation is even more complex when considering the exchange of structured information such as database records. To solve this problem, the Presentation layer provides a common representation of the data transferred. The :term:`ASN.1` notation was designed for the Presentation layer and is still used today by some protocols.
the `Application layer` that contains the mechanisms that do not fit in neither the Presentation nor the Session layer. The OSI Application layer was itself further divided in several generic service elements.
Footnotes

Loading…

No matching activity found.
Browse all component changes

Glossary

English English
No related strings found in the glossary.

String information

Flags
read-only
Source string location
../../principles/referencemodels.rst:207
String age
5 years ago
Source string age
5 years ago
Translation file
locale/pot/principles/referencemodels.pot, string 27