Zen

Translation

The initiating entity receives the `CA` segment. The acknowledgment number of this segment confirms that the remote entity has correctly received the `CR` segment. The transport connection is considered to be established by the initiating entity and the numbering of the data segments starts at sequence number `x`. Before sending data segments, the initiating entity must acknowledge the received `CA` segments by sending another `CA` segment.
0/4440 · 444

Sign in to save translations.

English Czech Actions
Connection establishment
 
An important difference between the connectionless service and the connection-oriented one is that the transport entities in the latter maintain some state during lifetime of the connection. This state is created when a connection is established and is removed when it is released.
 
Unfortunately, this scheme is not sufficient to ensure the reliability of the transport service. Consider for example a short-lived transport connection where a single, but important transfer (e.g. money transfer from a bank account) is sent. Such a short-lived connection starts with a `CR` segment acknowledged by a `CA` segment, then the data segment is sent, acknowledged and the connection terminates. Unfortunately, as the network layer service is unreliable, delays combined to retransmissions may lead to the situation depicted in the figure below, where a delayed `CR` and data segments from a former connection are accepted by the receiving entity as valid segments, and the corresponding data is delivered to the user. Duplicating SDUs is not acceptable, and the transport protocol must solve this problem.
 
To avoid these duplicates, transport protocols require the network layer to bound the `Maximum Segment Lifetime (MSL)`. The organization of the network must guarantee that no segment remains in the network for longer than `MSL` seconds. For example, on today's Internet, `MSL` is expected to be 2 minutes. To avoid duplicate transport connections, transport protocol entities must be able to safely distinguish between a duplicate `CR` segment and a new `CR` segment, without forcing each transport entity to remember all the transport connections that it has established in the past.
 
A classical solution to avoid remembering the previous transport connections to detect duplicates is to use a clock inside each transport entity. This `transport clock` has the following characteristics :
 
the `transport clock` is implemented as a `k` bits counter and its clock cycle is such that :math:`2^k \times cycle >> MSL`. Furthermore, the `transport clock` counter is incremented every clock cycle and after each connection establishment. This clock is illustrated in the figure below.
 
the `transport clock` must continue to be incremented even if the transport entity stops or reboots
 
Transport clock
 
It should be noted that `transport clocks` do not need and usually are not synchronized to the real-time clock. Precisely synchronizing real-time clocks is an interesting problem, but it is outside the scope of this document. See [Mills2006]_ for a detailed discussion on synchronizing the real-time clock.
 
This `transport clock` can now be combined with an exchange of three segments, called the `three way handshake`, to detect duplicates. This `three way handshake` occurs as follows :
 
The initiating transport entity sends a `CR` segment. This segment requests the establishment of a transport connection. It contains a port number (not shown in the figure) and a sequence number (`seq=x` in the figure below) whose value is extracted from the `transport clock`. The transmission of the `CR` segment is protected by a retransmission timer.
 
The remote transport entity processes the `CR` segment and creates state for the connection attempt. At this stage, the remote entity does not yet know whether this is a new connection attempt or a duplicate segment. It returns a `CA` segment that contains an acknowledgment number to confirm the reception of the `CR` segment (`ack=x` in the figure below) and a sequence number (`seq=y` in the figure below) whose value is extracted from its transport clock. At this stage, the connection is not yet established.
 
The initiating entity receives the `CA` segment. The acknowledgment number of this segment confirms that the remote entity has correctly received the `CR` segment. The transport connection is considered to be established by the initiating entity and the numbering of the data segments starts at sequence number `x`. Before sending data segments, the initiating entity must acknowledge the received `CA` segments by sending another `CA` segment.
 
The remote entity considers the transport connection to be established after having received the segment that acknowledges its `CA` segment. The numbering of the data segments sent by the remote entity starts at sequence number `y`.
 
The three way handshake is illustrated in the figure below.
 
Three-way handshake
 
Thanks to the three way handshake, transport entities avoid duplicate transport connections. This is illustrated by considering the three scenarios below.
 
The first scenario is when the remote entity receives an old `CR` segment. It considers this `CR` segment as a connection establishment attempt and replies by sending a `CA` segment. However, the initiating host cannot match the received `CA` segment with a previous connection attempt. It sends a control segment (`REJECT` in the figure below) to cancel the spurious connection attempt. The remote entity cancels the connection attempt upon reception of this control segment.
 
Three-way handshake : recovery from a duplicate `CR`
 
A second scenario is when the initiating entity sends a `CR` segment that does not reach the remote entity and receives a duplicate `CA` segment from a previous connection attempt. This duplicate `CA` segment cannot contain a valid acknowledgment for the `CR` segment as the sequence number of the `CR` segment was extracted from the transport clock of the initiating entity. The `CA` segment is thus rejected and the `CR` segment is retransmitted upon expiration of the retransmission timer.
 
Three-way handshake : recovery from a duplicate `CA`
 
Three-way handshake : recovery from duplicates `CR` and `CA`
 
Data transfer
 
Now that the transport connection has been established, it can be used to transfer data. To ensure a reliable delivery of the data, the transport protocol will include sliding windows, retransmission timers and `go-back-n` or `selective repeat`. However, we cannot simply reuse the techniques from the datalink because a transport protocol needs to deal with more types of errors than a reliable protocol in datalink layer. The first difference between the two layers is the transport layer must face with more variable delays. In the datalink layer, when two hosts are connected by a link, the transmission delay or the round-trip-time over the link is almost fixed. In a network that can span the globe, the delays and the round-trip-times can vary significantly on a per packet basis. This variability can be caused by two factors. First, packets sent through a network do not necessarily follow the same path to reach their destination. Second, some packets may be queued in the buffers of routers when the load is high and these queuing delays can lead to increased end-to-end delays. A second difference between the datalink layer and the transport layer is that a network does not always deliver packets in sequence. This implies that packets may be reordered by the network. Furthermore, the network may sometimes duplicate packets. The last issue that needs to be dealt with in the transport layer is the transmission of large SDUs. In the datalink layer, reliable protocols transmit small frames. Applications could generate SDUs that are much larger than the maximum size of a packet in the network layer. The transport layer needs to include mechanisms to fragment and reassemble these large SDUs.
 
To deal with all these characteristics of the network layer, we need to adapt the techniques that we have introduced in the datalink layer.
 

Loading…

User avatar None

Source string added
The initiating entity receives the `CA` segment. The acknowledgment number of this segment confirms that the remote entity has correctly received the `CR` segment. The transport connection is considered to be established by the initiating entity and the numbering of the data segments starts at sequence number `x`. Before sending data segments, the initiating entity must acknowledge the received `CA` segments by sending another `CA` segment.
6 years ago
Browse all string changes

Glossary

English Czech
No related strings found in the glossary.

18625 String information

Source string location
../../principles/transport.rst:670
String age
6 years ago
Last updated
4 months ago
Source string age
6 years ago
Translation file
locale/cs/LC_MESSAGES/principles/transport.po, string 122