cnp3-ebook/protocols/bgp — French @ Weblate: Besides the import and export filters, a key difference between …

Zen

Translation

English

French

Needs editing

Skip

	English	French	Actions
	Utilization of the BGP nexthop attribute
	This network contains three routers : `R1`, `R2` and `R3`. Each router is attached to a local IPv6 subnet that it advertises using BGP. There are two BGP sessions, one between `R1` and `R2` and the second between `R2` and `R3`. A `/127` subnet is used on each interdomain link (`2001:db8::4/127` on `R1-R2` and `2001:db8::0/127` on `R2-R3`) in conformance with the latest recommendation :rfc:`6164`. The BGP sessions run above TCP connections established between the neighboring routers (e.g. `2001:db8::5 - 2001:db8::6` for the `R1-R2` session).
	Let us assume that the `R1-R2` BGP session is the first to be established. A `BGP Update` message sent on such a session contains three fields :
	the advertised prefix
	the `BGP nexthop`
	the attributes including the AS-Path
	We use the notation `U(prefix, nexthop, attributes)` to represent such a `BGP Update` message in this section. Similarly, `W(prefix)` represents a `BGP withdraw` for the specified prefix. Once the `R1-R2` session has been established, `R1` sends `U(2001:db8:1234::/48,2001:db8::5,AS10)` to `R2` and `R2` sends `U(2001:db8:5678:/48,2001:db8::6,AS20)`. At this point, `R1` can reach `2001:db8:5678::/48` via `2001:db8::6` and `R2` can reach `2001:db8:1234::/48` via `2001:db8::5`.
	Once the `R2-R3` has been established, `R3` sends `U(2001:db8:acbd::/48,2001:db8::2,AS30)`. `R2` announces on the `R2-R3` session all the routes inside its RIB. It thus sends to `R3` : `U(2001:db8:1234::/48,2001:db8::1,AS20:AS10)` and `U(2001:db8:5678::/48,2001:db8::1,AS20)`. Note that when `R2` advertises the route that it learned from `R1`, it updates the BGP nexthop and adds its AS number to the AS-Path. `R2` also sends `U(2001:db8:abcd::48,2001:db8::6,AS20:AS30)` to `R1` on the `R1-R3` session. At this point, all BGP routes have been exchanged and all routers can reach `2001:db8::1234/48`, `2001:db8:5678::/48` and `2001:db8:abcd::/48`.
	If the link between `R2` and `R3` fails, `R3` detects the failure as it did not receive `KEEPALIVE` messages recently from `R2`. At this time, `R3` removes from its RIB all the routes learned over the `R2-R3` BGP session. `R2` also removes from its RIB the routes learned from `R3`. `R2` also sends `W(2001:db8:acbd::/48)` to `R1` over the `R1-R3` BGP session since it does not have a route anymore towards this prefix.
	Origin of the routes advertised by a BGP router
	A frequent practical question about the operation of BGP is how a BGP router decides to originate or advertise a route for the first time. In practice, this occurs in two situations :
	the router has been manually configured by the network operator to always advertise one or several routes on a BGP session. For example, on the BGP session between UCLouvain and its provider, belnet_ , UCLouvain's router always advertises the `2001:6a8:3080/48` IPv6 prefix assigned to the campus network
	the router has been configured by the network operator to advertise over its BGP session some of the routes that it learns with its intradomain routing protocol. For example, an enterprise router may advertise over a BGP session with its provider the routes to remote sites when these routes are reachable and advertised by the intradomain routing protocol
	The first solution is the most frequent. Advertising routes learned from an intradomain routing protocol is not recommended, this is because if the route flaps [#fflap]_, this would cause a large number of BGP messages being exchanged in the global Internet.
	The BGP decision process
	Besides the import and export filters, a key difference between BGP and the intradomain routing protocols is that each domain can define its own ranking algorithm to determine which route is chosen to forward packets when several routes have been learned towards the same prefix. This ranking depends on several BGP attributes that can be attached to a BGP route.
	The first BGP attribute that is used to rank BGP routes is the `local-preference` (local-pref) attribute. This attribute is an unsigned integer that is attached to each BGP route received over an eBGP session by the associated import filter.
	When comparing routes towards the same destination prefix, a BGP router always prefers the routes with the highest `local-pref`. If the BGP router knows several routes with the same `local-pref`, it prefers among the routes having this `local-pref` the ones with the shortest AS-Path.
	The `local-pref` attribute is often used to prefer some routes over others.
	A common utilization of `local-pref` is to support backup links. Consider the situation depicted in the figure below. `AS1` would always like to use the high bandwidth link to send and receive packets via `AS2` and only use the backup link upon failure of the primary one.
	How to create a backup link with BGP ?
	As BGP routers always prefer the routes with the highest `local-pref` attribute, this policy can be implemented using the following import filter on `R1`
	With this import filter, all the BGP routes learned from `RB` over the high bandwidth links are preferred over the routes learned over the backup link. If the primary link fails, the corresponding routes are removed from `R1`'s RIB and `R1` uses the route learned from `RA`. `R1` reuses the routes via `RB` as soon as they are advertised by `RB` once the `R1-RB` link comes back.
	The import filter above modifies the selection of the BGP routes inside `AS1`. Thus, it influences the route followed by the packets forwarded by `AS1`. In addition to using the primary link to send packets, `AS1` would like to receive its packets via the high bandwidth link. For this, `AS2` also needs to set the `local-pref` attribute in its import filter.
	Sometimes, the `local-pref` attribute is used to prefer a `cheap` link compared to a more expensive one. For example, in the network below, `AS1` could wish to send and receive packets mainly via its interdomain link with `AS4`.
	How to prefer a cheap link over an more expensive one ?
	`AS1` can install the following import filter on `R1` to ensure that it always sends packets via `R2` when it has learned a route via `AS2` and another via `AS4`.
	However, this import filter does not influence how `AS3` , for example, prefers some routes over others. If the link between `AS3` and `AS2` is less expensive than the link between `AS3` and `AS4`, `AS3` could send all its packets via `AS2` and `AS1` would receive packets over its expensive link. An important point to remember about `local-pref` is that it can be used to prefer some routes over others to send packets, but it has no influence on the routes followed by received packets.
	Another important utilization of the `local-pref` attribute is to support the `customer->provider` and `shared-cost` peering relationships. From an economic point of view, there is an important difference between these three types of peering relationships. A domain usually earns money when it sends packets over a `provider->customer` relationship. On the other hand, it must pay its provider when it sends packets over a `customer->provider` relationship. Using a `shared-cost` peering to send packets is usually neutral from an economic perspective. To take into account these economic issues, domains usually configure the import filters on their routers as follows :
	insert a high `local-pref` attribute in the routes learned from a customer
	insert a medium `local-pref` attribute in the routes learned over a shared-cost peering

Loading…

None

Source string added

English 0 characters edited

4 years ago

Browse all string changes

Glossary

English	French
No related strings found in the glossary.

30767 String information

Source string location

../../protocols/bgp.rst:306

String age

4 years ago

Last updated

2 months ago

Source string age

4 years ago

Translation file

locale/fr/LC_MESSAGES/protocols/bgp.po, string 78

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.