cnp3-ebook/protocols/tcp — French @ Weblate: When an `RST` segment is sent by a TCP entity, …

Zen

Translation

English

French

Needs editing

Skip

	English	French	Actions
	TCP fast retransmit heuristics
	When losses are not isolated or when the windows are small, the performance of the `fast retransmit` heuristic decreases. In such environments, it is necessary to allow a TCP sender to use a selective repeat strategy instead of the default go-back-n strategy. Implementing selective-repeat requires a change to the TCP protocol as the receiver needs to be able to inform the sender of the out-of-order segments that it has already received. This can be done by using the Selective Acknowledgments (SACK) option defined in :rfc:`2018`. This TCP option is negotiated during the establishment of a TCP connection. If both TCP hosts support the option, SACK blocks can be attached by the receiver to the segments that it sends. SACK blocks allow a TCP receiver to indicate the blocks of data that it has received correctly but out of sequence. The figure below illustrates the utilization of the SACK blocks.
	TCP selective acknowledgments
	A SACK option contains one or more blocks. A block corresponds to all the sequence numbers between the `left edge` and the `right edge` of the block. The two edges of the block are encoded as 32 bit numbers (the same size as the TCP sequence number) in an SACK option. As the SACK option contains one byte to encode its type and one byte for its length, a SACK option containing `b` blocks is encoded as a sequence of :math:`2+8 \times b` bytes. In practice, the size of the SACK option can be problematic as the optional TCP header extension cannot be longer than 40 bytes. As the SACK option is usually combined with the :rfc:`1323` timestamp extension, this implies that a TCP segment cannot usually contain more than three SACK blocks. This limitation implies that a TCP receiver cannot always place in the SACK option that it sends, information about all the received blocks.
	To deal with the limited size of the SACK option, a TCP receiver currently having more than 3 blocks inside its receiving buffer must select the blocks to place in the SACK option. A good heuristic is to put in the SACK option the blocks that have most recently changed, as the sender is likely to be already aware of the older blocks.
	When a sender receives a SACK option indicating a new block and thus a new possible segment loss, it usually does not retransmit the missing segments immediately. To deal with reordering, a TCP sender can use a heuristic similar to `fast retransmit` by retransmitting a gap only once it has received three SACK options indicating this gap. It should be noted that the SACK option does not supersede the `acknowledgment number` of the TCP header. A TCP sender can only remove data from its sending buffer once they have been acknowledged by TCP's cumulative acknowledgments. This design was chosen for two reasons. First, it allows the receiver to discard parts of its receiving buffer when it is running out of memory without loosing data. Second, as the SACK option is not transmitted reliably, the cumulative acknowledgments are still required to deal with losses of `ACK` segments carrying only SACK information. Thus, the SACK option only serves as a hint to allow the sender to optimize its retransmissions.
	As explained earlier, the TCP Timestamp option :rfc:`1323` prevents ambiguities while collecting round-trip-time measurements. It plays another very important role in today's high-bandwidth networks. Since TCP uses 32 bits long sequence numbers, the sequence numbers wrap after the transmission of 4 GBytes of data. With 10 Gbps and soon 100 Gbps interfaces, TCP only needs to transmit during a few seconds before reusing the same sequence number. Given that the Maximum Segment Lifetime is still 2 minutes, several packets, belonging to the same TCP connection could use the same sequence number. If one of these packets is severely delayed through the network, it could reappear at the same time as a packet with the same TCP sequence number. To prevent this problem, most modern TCP implementations associate a TCP timestamp option to each segment on transmission. When a TCP stack receives a TCP segment, it checks that its TCP timestamp is valid and if not the segment is discarded :rfc:`7323`.
	TCP connection release
	TCP, like most connection-oriented transport protocols, supports two types of connection releases :
	graceful connection release, where each TCP user can release its own direction of data transfer after having transmitted all data
	abrupt connection release, where either one user closes both directions of data transfer or one TCP entity is forced to close the connection (e.g., because the remote host does not reply anymore or due to lack of resources)
	The abrupt connection release mechanism is very simple and relies on a single segment having the `RST` bit set. A TCP segment containing the `RST` bit can be sent for the following reasons :
	a non-`SYN` segment was received for a non-existing TCP connection :rfc:`793`
	by extension, some implementations respond with an `RST` segment to a segment that is received on an existing connection but with an invalid header :rfc:`3360`. This causes the corresponding connection to be closed and has caused security attacks :rfc:`4953`
	by extension, some implementations send an `RST` segment when they need to close an existing TCP connection (e.g., because there are not enough resources to support this connection or because the remote host is considered to be unreachable). Measurements have shown that this usage of TCP `RST` is widespread [AW05]_
	When an `RST` segment is sent by a TCP entity, it should contain the current value of the `sequence number` for the connection (or 0 if it does not belong to any existing connection) and the `acknowledgment number` should be set to the next expected in-sequence `sequence number` on this connection.
	TCP `RST` wars
	The designers of TCP implementations should ensure that two TCP entities never enter a TCP `RST` war where host `A` is sending a `RST` segment in response to a previous `RST` segment that was sent by host `B` in response to a TCP `RST` segment sent by host `A` ... To avoid such an infinite exchange of `RST` segments that do not carry data, a TCP entity is never allowed to send a `RST` segment in response to another `RST` segment.
	The normal way of terminating a TCP connection is by using the graceful TCP connection release. This mechanism uses the `FIN` flag of the TCP header and allows each host to release its own direction of data transfer. As for the `SYN` flag, the utilization of the `FIN` flag in the TCP header consumes one sequence number. The figure :ref:`fig-tcprelease` shows the part of the TCP FSM used when a TCP connection is released.
	Starting from the `Established` state, there are two main paths through this FSM.
	The first path is when the host receives a segment with sequence number `x` and the `FIN` flag set. The utilization of the `FIN` flag indicates that the byte before `sequence number` `x` was the last byte of the byte stream sent by the remote host. Once all of the data has been delivered to the user, the TCP entity sends an `ACK` segment whose `ack` field is set to :math:`(x+1) \pmod{2^{32}}` to acknowledge the `FIN` segment. The `FIN` segment is subject to the same retransmission mechanisms as a normal TCP segment. In particular, its transmission is protected by the retransmission timer. At this point, the TCP connection enters the `CLOSE\_WAIT` state. In this state, the host can still send data to the remote host. Once all its data have been sent, it sends a `FIN` segment and enter the `LAST\_ACK` state. In this state, the TCP entity waits for the acknowledgment of its `FIN` segment. It may still retransmit unacknowledged data segments, e.g., if the retransmission timer expires. Upon reception of the acknowledgment for the `FIN` segment, the TCP connection is completely closed and its :term:`TCB` can be discarded.
	The `TIME\_WAIT` state is different from the other states of the TCP FSM. A TCP entity enters this state after having sent the last `ACK` segment on a TCP connection. This segment indicates to the remote host that all the data that it has sent have been correctly received and that it can safely release the TCP connection and discard the corresponding :term:`TCB`. After having sent the last `ACK` segment, a TCP connection enters the `TIME\_WAIT` and remains in this state for :math:`2MSL` seconds. During this period, the TCB of the connection is maintained. This ensures that the TCP entity that sent the last `ACK` maintains enough state to be able to retransmit this segment if this `ACK` segment is lost and the remote host retransmits its last `FIN` segment or another one. The delay of :math:`2MSL` seconds ensures that any duplicate segments on the connection would be handled correctly without causing the transmission of an `RST` segment. Without the `TIME\_WAIT` state and the :math:`2*MSL` seconds delay, the connection release would not be graceful when the last `ACK` segment is lost.
	TIME\_WAIT on busy TCP servers
	Footnotes
	A detailed presentation of all standardization documents concerning TCP may be found in :rfc:`4614`
	Several researchers have analyzed the utilization of TCP and UDP in the global Internet. Most of these studies have been performed by collecting all the packets transmitted over a given link during a period of a few hours or days and then analyzing their headers to infer the transport protocol used, the type of application, ... Recent studies include http://www.caida.org/research/traffic-analysis/tcpudpratio/, https://research.sprintlabs.com/packstat/packetoverview.php or http://www.nanog.org/meetings/nanog43/presentations/Labovitz_internetstats_N43.pdf
	This 32 bits counter was specified in :rfc:`793`. A 32 bits counter that is incremented every 4 microseconds wraps in about 4.5 hours. This period is much larger than the Maximum Segment Lifetime that is fixed at 2 minutes in the Internet (:rfc:`791`, :rfc:`1122`).
	On many departmental networks containing Unix workstations, it was common to allow users on one of the hosts to use ``rlogin`` :rfc:`1258` to run commands on any of the workstations of the network without giving any password. In this case, the remote workstation "authenticated" the client host based on its IP address. This was a bad practice from a security viewpoint.
	Of course, such a simultaneous TCP establishment can only occur if the source port chosen by the client is equal to the destination port chosen by the server. This may happen when a host can serve both as a client as a server or in peer-to-peer applications when the communicating hosts do not use ephemeral port numbers.

Loading…

None

Source string added

English 0 characters edited

4 years ago

Browse all string changes

Glossary

English	French
No related strings found in the glossary.

32125 String information

Source string location

../../protocols/tcp.rst:561

String age

4 years ago

Last updated

2 months ago

Source string age

4 years ago

Translation file

locale/fr/LC_MESSAGES/protocols/tcp.po, string 173

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.