Exit Zen
170
../../glossary.rst:110
English
A packet is said to be spoofed when the sender of the packet has used as source address a different address than its own.
0/1210 · 121
170
../../principles/linkstate.rst:16
English
weight proportional to the propagation delay on the link. If all link weights are configured this way, shortest path routing uses the paths with the smallest propagation delay.
0/1760 · 176
170
../../principles/reliability.rst:703
English
The sliding window
0/180 · 18
170
../../principles/sharing.rst:775
English
Evolution of the transmission rates
0/350 · 35
171
../../principles/linkstate.rst:17
English
:math:`weight=\frac{C}{bandwidth}` where `C` is a constant larger than the highest link bandwidth in the network. If all link weights are configured this way, shortest path routing prefers higher bandwidth paths over lower bandwidth paths.
0/2390 · 239
171
../../principles/sharing.rst:778
English
Various types of rate adaption algorithms are possible. `Dah Ming Chiu`_ and `Raj Jain`_ have analyzed, in [CJ1989]_, different types of algorithms that can be used by a source to adapt its transmission rate to the feedback received from the network. Intuitively, such a rate adaptation algorithm increases the transmission rate when the network is not congested (ensure that the network is efficiently used) and decrease the transmission rate when the network is congested (to avoid congestion collapse).
0/5050 · 505
172
../../glossary.rst:203
English
The Secure Shell (SSH) Transport Layer Protocol is defined in :rfc:`4253`
0/730 · 73
172
../../principles/linkstate.rst:19
English
Usually, the same weight is associated to the two directed edges that correspond to a physical link (i.e. :math:`R1 \rightarrow R2` and :math:`R2 \rightarrow R1`). However, nothing in the link state protocols requires this. For example, if the weight is set in function of the link bandwidth, then an asymmetric ADSL link could have a different weight for the upstream and downstream directions. Other variants are possible. Some networks use optimization algorithms to find the best set of weights to minimize congestion inside the network for a given traffic demand [FRT2002]_.
0/5790 · 579
172
../../principles/reliability.rst:712
English
Sliding window example
0/220 · 22
172
../../principles/sharing.rst:780
English
The simplest form of feedback that the network can send to a source is a binary feedback (the network is congested or not congested). In this case, a `linear` rate adaptation algorithm can be expressed as :
0/2060 · 206
173
../../glossary.rst:301
English
standard query
0/140 · 14
173
../../principles/linkstate.rst:24
English
When a link-state router boots, it first needs to discover to which routers it is directly connected. For this, each router sends a HELLO message every `N` seconds on all its interfaces. This message contains the router's address. Each router has a unique address. As its neighboring routers also send HELLO messages, the router automatically discovers to which neighbors it is connected. These HELLO messages are only sent to neighbors that are directly connected to a router, and a router never forwards the HELLO messages that it receives. HELLO messages are also used to detect link and router failures. A link is considered to have failed if no HELLO message has been received from a neighboring router for a period of :math:`k \times N` seconds.
0/7510 · 751
173
../../principles/reliability.rst:715
English
In practice, as the frame header includes an `n` bits field to encode the sequence number, only the sequence numbers between :math:`0` and :math:`2^{n}-1` can be used. This implies that, during a long transfer, the same sequence number will be used for different frames and the sliding window will wrap. This is illustrated in the figure below assuming that `2` bits are used to encode the sequence number in the frame header. Note that upon reception of `OK1`, the sender slides its window and can use sequence number `0` again.
0/5290 · 529
173
../../principles/sharing.rst:782
English
:math:`rate(t+1)=\alpha_C + \beta_C rate(t)` when the network is congested
0/740 · 74
174
../../glossary.rst:303
English
For DNS servers and resolvers, a standard query is a query for a `A` or a `AAAA` record. Such a query typically returns an IP address.
0/1340 · 134
174
../../principles/reliability.rst:722
English
Utilisation of the sliding window with modulo arithmetic
0/560 · 56
174
../../principles/sharing.rst:783
English
:math:`rate(t+1)=\alpha_N + \beta_N rate(t)` when the network is *not* congested
0/800 · 80
175
../../glossary.rst:177
English
switch
0/100 · 6
175
../../principles/linkstate.rst:33
English
Once a router has discovered its neighbors, it must reliably distribute all its outgoing edges to all routers in the network to allow them to compute their local view of the network topology. For this, each router builds a `link-state packet` (LSP) containing the following information:
0/2860 · 286
175
../../principles/reliability.rst:727
English
Unfortunately, frame losses do not disappear because a reliable protocol uses a sliding window. To recover from losses, a sliding window protocol must define :
0/1590 · 159