Exit Zen
179
../../protocols/ipv6.rst:633
English
The IPv6 subnet
0/150 · 15
179
../../protocols/wifi.rst:135
English
In addition to the data and control frames that we have briefly described above, 802.11 networks use several types of management frames. These management frames are used for various purposes. We briefly describe some of these frames below. A detailed discussion may be found in [IEEE802.11]_ and [Gast2002]_.
0/3080 · 308
180
../../glossary.rst:116
English
The Transmission Control Block is the set of variables that are maintained for each established TCP connection by a TCP implementation.
0/1350 · 135
180
../../principles/linkstate.rst:42
English
These LSPs must be reliably distributed inside the network without using the router's routing table since these tables can only be computed once the LSPs have been received. The `Flooding` algorithm is used to efficiently distribute the LSPs of all routers. Each router that implements `flooding` maintains a `link state database` (LSDB) containing the most recent LSP sent by each router. When a router receives a LSP, it first verifies whether this LSP is already stored inside its LSDB. If so, the router has already distributed the LSP earlier and it does not need to forward it. Otherwise, the router forwards the LSP on all its links except the link over which the LSP was received. Flooding can be implemented by using the following pseudo-code.
0/7520 · 752
180
../../protocols/email.rst:289
English
0x14
0/100 · 4
180
../../protocols/ipv6.rst:635
English
Until now, we have focused our discussion on the utilization of IPv6 on point-to-point links. Although there are point-to-point links in the Internet, mainly between routers and sometimes hosts, most of the hosts are attached to datalink layer networks such as Ethernet LANs or WiFi networks. These datalink layer networks play an important role in today's Internet and have heavily influenced the design of the operation of IPv6. To understand IPv6 and ICMPv6 completely, we first need to correctly understand the key principles behind these datalink layer technologies.
0/5710 · 571
180
../../protocols/wifi.rst:141
English
A first type of management frames are the `beacon` frames. These frames are broadcasted regularly by access points. Each `beacon frame` contains information about the capabilities of the access point (e.g. the supported 802.11 transmission rates) and a `Service Set Identity` (SSID). The SSID is a null-terminated ASCII string that can contain up to 32 characters. An access point may support several SSIDs and announce them in beacon frames. An access point may also choose to remain silent and not advertise beacon frames. In this case, WiFi stations may send `Probe request` frames to force the available access points to return a `Probe response` frame.
0/6570 · 657
180
../../protocols/tcp.rst:609
English
The `TIME\_WAIT` state is different from the other states of the TCP FSM. A TCP entity enters this state after having sent the last `ACK` segment on a TCP connection. This segment indicates to the remote host that all the data that it has sent have been correctly received and that it can safely release the TCP connection and discard the corresponding :term:`TCB`. After having sent the last `ACK` segment, a TCP connection enters the `TIME\_WAIT` and remains in this state for :math:`2*MSL` seconds. During this period, the TCB of the connection is maintained. This ensures that the TCP entity that sent the last `ACK` maintains enough state to be able to retransmit this segment if this `ACK` segment is lost and the remote host retransmits its last `FIN` segment or another one. The delay of :math:`2*MSL` seconds ensures that any duplicate segments on the connection would be handled correctly without causing the transmission of an `RST` segment. Without the `TIME\_WAIT` state and the :math:`2*MSL` seconds delay, the connection release would not be graceful when the last `ACK` segment is lost.
0/11020 · 1102
181
../../glossary.rst:87
English
TCP
0/100 · 3
181
../../principles/sharing.rst:830
English
Consider first a window of one segment. This segment takes 4 msec to reach host `D`. The destination replies with an acknowledgment and the next segment can be transmitted. With such a sending window, the transmission rate is roughly 250 segments per second or 250 Kbps. This is illustrated in the figure below where each square of the grid corresponds to one millisecond.
0/3720 · 372
181
../../protocols/email.rst:291
English
00010100
0/100 · 8
181
../../protocols/ipv6.rst:637
English
As explained earlier, devices attached to a Local Area Network can directly exchange frames among themselves. For this, each datalink layer interface on a device (host, router, ...) attached to such a network is identified by a MAC address. Each datalink layer interface includes a unique hardwired MAC address. MAC addresses are allocated to manufacturers in blocks and interface is numbered with a unique address. Thanks to the global unicity of the MAC addresses, the datalink layer service can assume that two hosts attached to a LAN have different addresses. Most LANs provide an unreliable connectionless service and a datalink layer frame has a header containing :
0/6710 · 671
181
../../protocols/wifi.rst:144
English
IP over 802.11
0/140 · 14
181
../../protocols/tcp.rst:611
English
TIME\_WAIT on busy TCP servers
0/300 · 30
182
../../glossary.rst:89
English
The Transmission Control Protocol is a protocol of the transport layer in the TCP/IP protocol suite that provides a reliable bytestream connection-oriented service on top of IP
0/1760 · 176
182
../../principles/linkstate.rst:59
English
Which is the most recent LSP ?
0/300 · 30
182
../../principles/sharing.rst:878
English
Consider now a window of two segments. Host `A` can send two segments within 2 msec on its 1 Mbps link. If the first segment is sent at time :math:`t_{0}`, it reaches host `D` at :math:`t_{0}+4`. Host `D` replies with an acknowledgment that opens the sending window on host `A` and enables it to transmit a new segment. In the meantime, the second segment was buffered by router `R1`. It reaches host `D` at :math:`t_{0}+6` and an acknowledgment is returned. With a window of two segments, host `A` transmits at roughly 500 Kbps, i.e. the transmission rate of the bottleneck link.
0/5800 · 580
182
../../protocols/email.rst:293
English
000101 000000
0/130 · 13
182
../../protocols/ipv6.rst:639
English
the source MAC address
0/220 · 22
182
../../protocols/wifi.rst:146
English
Two types of encapsulation schemes were defined to support IP in Ethernet networks : the original encapsulation scheme, built above the Ethernet DIX format is defined in :rfc:`894` and a second encapsulation :rfc:`1042` scheme, built above the LLC/SNAP protocol [IEEE802.2]_. In 802.11 networks, the situation is simpler and only the :rfc:`1042` encapsulation is used. In practice, this encapsulation adds 6 bytes to the 802.11 header. The first four bytes correspond to the LLC/SNAP header. They are followed by the two bytes Ethernet Type field (`0x800` for IP and `0x806` for ARP). The figure below shows an IP packet encapsulated in an 802.11 frame.
0/6530 · 653