cnp3-ebook/exercises/ipv6 — English @ Weblate

Exit Zen

76 ../../exercises/ipv6.rst:696

	English To help students to start using IPMininet, `Mathieu Jadin <https://inl.info.ucl.ac.be/mjadin.html>`_ has created a Vagrant box that launches a Ubuntu virtual machine with all the required software. See https://ipmininet.readthedocs.io/en/latest/install.html for additional information. 285/10000 · 285
77 ../../exercises/ipv6.rst:698

	English Here is a simple example of the utilization of this Vagrant box. 64/10000 · 64
78 ../../exercises/ipv6.rst:700

	English We start the network topology shown above with the ``sudo python script.py`` command. It launches the mininet_ interactive shell that provides several useful commands: 167/10000 · 167
79 ../../exercises/ipv6.rst:732

	English Some of the standard mininet commands assume the utilisation of IPv4 and do not have a direct IPv6 equivalent. Here are some useful commands. 141/10000 · 141
80 ../../exercises/ipv6.rst:734

	English The ``nodes`` command lists the routers and hosts that have been created in the mininet topology. 97/10000 · 97
81 ../../exercises/ipv6.rst:743

	English The ``links`` command lists the links that have been instantiated and shows that mapping between the named interfaces on each node. 131/10000 · 131
82 ../../exercises/ipv6.rst:760

	English It is possible to execute any of the standard Linux commands to configure the network stack on any of the hosts by prefixing the command with the corresponding host. Remember to always specify ``inet6`` as the address family to retrieve the IPv6 information. 258/10000 · 258
83 ../../exercises/ipv6.rst:770

	English Host ``a`` has two interfaces: the standard loopback interface and a network interface named ``a-eth0`` that is attached to router ``r1``. We can also verify how the IPv6 addresses have been configured: 202/10000 · 202
84 ../../exercises/ipv6.rst:784

	English On its ``a-eth0`` interface, host ``a`` uses IPv6 address ``2001:db8:1341:1::a/64``. The link local address (``fe80::c44e:26ff:fed9:de6d/64``) will be described in another chapter. Finally, we can check the forwarding table of host ``a``. 238/10000 · 238
85 ../../exercises/ipv6.rst:794

	English There are three routes in this table. The first two correspond to the two prefixes that are used over the ``a-eth0`` interface. These routes are automatically created when an IPv6 address is configured on an interface. The last route is the default route (``::/0``) which points towards ``2001:db8:1341:1::1``, i.e. router ``r1``. 330/10000 · 330
86 ../../exercises/ipv6.rst:796

	English Another useful command is ``xterm`` 'node' that allows to launch a terminal on the specified node. This gives you a interactive shell on any node. You can use it to capture packets with tcpdump_. As an example, let us use :manpage:`traceroute6(8)` to trace the path followed by packets from host ``a`` towards the IPv6 address of host ``b`` i.e. ``2001:db8:1341:3::b``. The output of this command shows that the path passes through routers ``r1``, ``r2`` and ``r3``. 466/10000 · 466
87 ../../exercises/ipv6.rst:808

	English Another interesting mininet_ command is ``pingall`` it allows to check that any host can reach any other host inside the network. It executes a ping from any host to any other host inside the network topology. 209/10000 · 209
88 ../../exercises/ipv6.rst:819

	English When debugging a network, it can be interesting to capture packets using tcpdump_ on specific links to check that they follow the expect. If you use tcpdump_ without any filter, you will capture the packets generated by xterm. To capture packets, you need to specify precise filters that will match the packets of interest. For traceroute6, you need to match the IPv6 packets that contain UDP segments and some ICMPv6 packets. The script below provides a simple filter that you can reuse. It takes one argument: the name of the interface on which tcpdump_ needs to run. 569/10000 · 569
89 ../../exercises/ipv6.rst:827

	English Starting from the :download:`/exercises/ipmininet_scripts/static-1.py` IPMininet_ script, we can explore classical problems when networks are configured with static routes. A first problem is when a router has an incomplete forwarding table. We configure the static routes as shown below. The entire script is available from :download:`/exercises/ipmininet_scripts/static-1-hole.py`. 383/10000 · 383
90 ../../exercises/ipv6.rst:841

	English We first check with ``pingall`` whether the network works correctly. 68/10000 · 68
91 ../../exercises/ipv6.rst:851

	English The problem can be detected by using :manpage:`traceroute6(8)`. 63/10000 · 63
92 ../../exercises/ipv6.rst:861

	English In the output of :manpage:`traceroute6(8)`, a ``!N`` indicates that host ``a`` received from ``2001:db8:1341:12::2``, i.e. router ``r2``, a Network unreachable ICMPv6 message. The forwarding table of ``r2`` confirms the root cause of this problem. 247/10000 · 247
93 ../../exercises/ipv6.rst:873

	English A second problem is when there is a forwarding loop inside the network, i.e. packets sent to a specific destination loop through several routers. With the static routes shown below, router ``r2`` forwards the packets towards ``2001:db8:1341:3::b`` via router ``r1``. The entire script is available from :download:`/exercises/ipmininet_scripts/static-1-loop.py`. 361/10000 · 361
94 ../../exercises/ipv6.rst:888

	English The ``pingall`` command reveals that there is a problem in this network. 72/10000 · 72
95 ../../exercises/ipv6.rst:898

	English We can analyze this configuration problem in more details by using ``traceroute6``. The loop appears clearly. 109/10000 · 109

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.