cnp3-ebook/exercises/network — English @ Weblate

Exit Zen

62 ../../exercises/network.rst:375 • ../../exercises/network.rst:375

	English 1 via D 7/10000 · 7
63 ../../exercises/network.rst:376

	English E 1/10000 · 1
64 ../../exercises/network.rst:376

	English 4 via B 7/10000 · 7
65 ../../exercises/network.rst:376

	English 1 via E 7/10000 · 7
66 ../../exercises/network.rst:379

	English Distance vector protocols can operate in two different modes : `periodic updates` and `triggered updates`. `Periodic updates` is the default mode for a distance vector protocol. For example, each router could advertise its distance vector every thirty seconds. With the `triggered updates` a router sends its distance vector when its routing table changes (and periodically when there are no changes). 401/10000 · 401
67 ../../exercises/network.rst:381

	English Consider a distance vector protocol using split horizon and `periodic updates`. Assume that the link `B-C` fails. `B` and `C` update their local routing table but they will only advertise it at the end of their period. Select one ordering for the `periodic updates` and every time a router sends its distance vector, indicate the vector sent to each neighbor and update the table above. How many periods are required to allow the network to converge to a stable state ? 470/10000 · 470
68 ../../exercises/network.rst:383

	English Consider the same distance vector protocol, but now with `triggered updates`. When link `B-C` fails, assume that `B` updates its routing table immediately and sends its distance vector to `A` and `D`. Assume that both `A` and `D` process the received distance vector and that `A` sends its own distance vector, ... Indicate all the distance vectors that are exchanged and update the table above each time a distance vector is sent by a router (and received by other routers) until all routers have learned a new route to each destination. How many distance vector messages must be exchanged until the network converges to a stable state ? 638/10000 · 638
69 ../../exercises/network.rst:385

	English Consider again the network shown above. After some time, link state routing converges and all routers compute the same routing tables as above. 143/10000 · 143
70 ../../exercises/network.rst:387

	English An important difference between OSPF and RIP is that OSPF routers flood link state packets that allow the other routers to recompute their own routing tables while RIP routers exchange distance vectors. Consider that link `B-C` fails and that router `B` is the first to detect the failure. At this point, `B` cannot reach anymore `C`, `D` and `E`. `C` cannot reach `B` and `A` anymore. 385/10000 · 385
71 ../../exercises/network.rst:389

	English Router `B` will flood its updated link state packet through the entire network and all routers will recompute their forwarding table. Upon reception of a link state packet, routers usually first flood the received link-state packet and then recompute their forwarding table. Assume that `B` is the first to recompute its forwarding table, followed by `D`, `A`, `C` and finally `E`. 381/10000 · 381
72 ../../exercises/network.rst:391

	English After each update of a forwarding table, verify which pairs of routers are able to exchange packets. Provide your answer using a table similar to the one shown above. 166/10000 · 166
The translation has come to an end.

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.