cnp3-ebook/exercises/routing-protocols

Exit Zen

1 ../../exercises/routing-protocols.rst:7
	English Exploring routing protocols
	French Découverte des protocoles de routage 36/270 · 27 Needs editing
2 ../../exercises/routing-protocols.rst:9
	English Routing protocols play a key role in the Internet since they ensure that all the routers have valid routing tables. In this section, we use IPMininet_ to explore how intradomain and interdomain routing protocols work in practice. IPMininet_ adds an abstraction layer above the actual configuration of the FRRouting daemons that implement these routing protocols.
	French 0/3620 · 362 Needs editing
3 ../../exercises/routing-protocols.rst:13
	English Exploring OSPF
	French 0/140 · 14 Needs editing
4 ../../exercises/routing-protocols.rst:15
	English We first use IPMininet_ to explore the operation of OSPFv3, the version of OSPF that supports IPv6. We create a simple network with three routers and two hosts as shown in the figure below.
	French 0/1890 · 189 Needs editing
5 ../../exercises/routing-protocols.rst:80
	English The code is very simple as by default IPMininet_ enables OSPF on routers. We introduce two specific parameters. First, the interface that connects a router to a host is flagged as a passive interface (``igp_passive=True``). This indicates to the router that there are no other routers attached to this interface and that it should not send or accept OSPF Hello messages on this interface. The second configuration parameter is that we set the IGP cost on each link.
	French 0/4650 · 465 Needs editing
6 ../../exercises/routing-protocols.rst:83
	English We use this mininet_ topology to collect packet traces that show the packets that OSPF routers exchange. For this, we add the following ``post_build`` method that IPMininet_ starts after having constructed the network and before launching the daemons. It simply starts tcpdump_ on each router to collect the first 100 OSPF packets that they send/receive.
	French 0/3540 · 354 Needs editing
7 ../../exercises/routing-protocols.rst:94
	English Finally, we can start the IPMininet_ topology and launch the daemons. The entire script is available from :download:`/exercises/ipmininet_scripts/ospf6.py`.
	French 0/1560 · 156 Needs editing
8 ../../exercises/routing-protocols.rst:106
	English The script starts the routers and hosts.
	French 0/400 · 40 Needs editing
9 ../../exercises/routing-protocols.rst:120
	English We can easily verify that the paths used to forward packets are the expected ones according to the configured IGP weights.
	French 0/1220 · 122 Needs editing
10 ../../exercises/routing-protocols.rst:135
	English We can also connect to the OSPFv3 daemon running on the routers to observe its state. For this, we use the ``noecho r1 telnet localhost ospf6d`` command.
	French 0/1530 · 153 Needs editing
11 ../../exercises/routing-protocols.rst:152
	English The password to access this daemon is `zebra`. It supports various commands that are described in the `FRRouting documentation <http://docs.frrouting.org/en/latest/ospf6d.html#showing-ospf6-information>`_ We briefly illustrate some of them below.
	French 0/2460 · 246 Needs editing
12 ../../exercises/routing-protocols.rst:175
	English The ``show ipv6 ospf6`` command reports the general state of the OSPFv3 daemon. The ``show ipv6 ospf6 neighbor`` command reports the state of the connected neighbors.
	French 0/1660 · 166 Needs editing
13 ../../exercises/routing-protocols.rst:186
	English In its output, we see that ``r1`` is attached to two different routers. Finally, the ``show ipv6 ospf6 database`` returns the full OSPFv3 database with all the link state information that was distributed by OSPFv3.
	French 0/2140 · 214 Needs editing
14 ../../exercises/routing-protocols.rst:239
	English We can also use the packet traces that were collected by tcpdump_ to observe the packets that the OSPFv3 daemons exchange. OSPFv3 is a more complex protocol that the basic link state protocol that we have described in this book, but you should be able to understand some of these packets. The packet traces are available as :download:`/exercises/traces/ospf6-r1-trace.pcap`, :download:`/exercises/traces/ospf6-r2-trace.pcap` and :download:`/exercises/traces/ospf6-r3-trace.pcap`. Here are a few interesting packets collected on router ``r1``.
	French 0/5420 · 542 Needs editing
15 ../../exercises/routing-protocols.rst:241
	English The first packet that this router received his a Hello packet that was sent by router ``r2``. There are several interesting points to note about this packet. First, its source address is the link-local address (``fe80::68bc:b4ff:fe19:42b7``) of router ``r2`` on this interface. The destination address of the packet is reserved IPv6 multicast address for OSPFv3, i.e. ``ff02::5``. The Hop Limit of the packet is set to 1 and OSFPv3 uses a next header of type 89.
	French 0/4620 · 462 Needs editing
16 ../../exercises/routing-protocols.rst:245
	English The Hello packet contains some parameters such as the `Hello interval` that is set to 1 second. This interval is the delay between the transmission of successive Hello packets. Since the `Router Dead Interval` is set to 3 seconds, the router will consider the link as down if it does not receive Hello packets during a period of 3 seconds. The second packet of the trace is sent by router ``r1``.
	French 0/3960 · 396 Needs editing
17 ../../exercises/routing-protocols.rst:249
	English We can then observe the Database description packet that is sent by routers to announce the state of their OSPFv3 database. The details of this packet are beyond the scope of this simple exercise.
	French 0/1960 · 196 Needs editing
18 ../../exercises/routing-protocols.rst:253
	English This packet is updated when new information is added in the router's OSPFv3 database. A few seconds router, this router sends another Database description packet that announces more information.
	French 0/1940 · 194 Needs editing
19 ../../exercises/routing-protocols.rst:257
	English Router ``r2`` reacts to this updated Database description packet by requesting the link state information that it does not already know. For this, it sends a `LS Request` packet.
	French 0/1780 · 178 Needs editing
20 ../../exercises/routing-protocols.rst:261
	English The requested information is sent in a `LS Update` packet shortly after that.
	French 0/770 · 77 Needs editing

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.