Exit Zen
27
../../principles/reliability.rst:70
English
This transmission scheme has been used in some early networks. We use it as a basis to understand how hosts communicate. From a Computer Science viewpoint, dealing with voltages is unusual. Computer scientists frequently rely on models that enable them to reason about the issues that they face without having to consider all implementation details. The physical transmission scheme described above can be represented by using a `time-sequence diagram`.
0/4540 · 454
31
../../principles/reliability.rst:106
English
With the above transmission scheme, a bit is transmitted by setting the voltage on the electrical cable to a specific value during some period of time. We have seen that due to electromagnetic interference, the voltage measured by the receiver can differ from the voltage set by the transmitter. This is the main cause of transmission errors. However, this is not the only type of problem that can occur. Besides defining the voltages for bits `0` and `1`, the above transmission scheme also specifies the duration of each bit. If one million bits are sent every second, then each bit lasts 1 microsecond. On each host, the transmission (resp. the reception) of each bit is triggered by a local clock having a 1 MHz frequency. These clocks are the second source of problems when transmitting bits over a wire. Although the two clocks have the same specification, they run on different hosts, possibly at a different temperature and with a different source of energy. In practice, it is possible that the two clocks do not operate at exactly the same frequency. Assume that the clock of the transmitting host operates at exactly 1000000 Hz while the receiving clock operates at 999999 Hz. This is a very small difference between the two clocks. However, when using the clock to transmit bits, this difference is important. With its 1000000 Hz clock, the transmitting host will generate one million bits during a period of one second. During the same period, the receiving host will sense the wire 999999 times and thus will receive one bit less than the bits originally transmitted. This small difference in clock frequencies implies that bits can "disappear" during their transmission on an electrical cable. This is illustrated in the figure below.
0/17490 · 1749
32
../../principles/reliability.rst:128
English
A similar reasoning applies when the clock of the sending host is slower than the clock of the receiving host. In this case, the receiver will sense more bits than the bits that have been transmitted by the sender. This is illustrated in the figure below where the second bit received on the right was not transmitted by the left host.
0/3350 · 335
34
../../principles/reliability.rst:152
English
the `Physical layer service` may change, e.g. due to electromagnetic interference, the value of a bit being transmitted
0/1190 · 119
35
../../principles/reliability.rst:153
English
the `Physical layer service` may deliver `more` bits to the receiver than the bits sent by the sender
0/1010 · 101
36
../../principles/reliability.rst:154
English
the `Physical layer service` may deliver `fewer` bits to the receiver than the bits sent by the sender
0/1020 · 102
37
../../principles/reliability.rst:160
English
Many other types of encodings have been defined to transmit information over an electrical cable. All physical layers are able to send and receive physical symbols that represent values `0` and `1`. However, for various reasons that are outside the scope of this chapter, several physical layers exchange other physical symbols as well. For example, the Manchester encoding used in several physical layers can send four different symbols. The Manchester encoding is a differential encoding scheme in which time is divided into fixed-length periods. Each period is divided in two halves and two different voltage levels can be applied. To send a symbol, the sender must set one of these two voltage levels during each half period. To send a `1` (resp. `0`), the sender must set a high (resp. low) voltage during the first half of the period and a low (resp. high) voltage during the second half. This encoding ensures that there will be a transition at the middle of each period and allows the receiver to synchronize its clock to the sender's clock. Apart from the encodings for `0` and `1`, the Manchester encoding also supports two additional symbols : `InvH` and `InvB` where the same voltage level is used for the two half periods. By definition, these two symbols cannot appear inside a frame which is only composed of `0` and `1`. Some technologies use these special symbols as markers for the beginning or end of frames.
0/14290 · 1429
38
../../principles/reliability.rst:167
English
Manchester encoding
0/190 · 19
40
../../principles/reliability.rst:180
English
All the functions related to the physical transmission or information through a wire (or a wireless link) are usually known as the `physical layer`. The physical layer allows thus two or more entities that are directly attached to the same transmission medium to exchange bits. Being able to exchange bits is important as virtually any information can be encoded as a sequence of bits. Electrical engineers are used to processing streams of bits, but computer scientists usually prefer to deal with higher level concepts. A similar issue arises with file storage. Storage devices such as hard-disks also store streams of bits. There are hardware devices that process the bit stream produced by a hard-disk, but computer scientists have designed filesystems to allow applications to easily access such storage devices. These filesystems are typically divided into several layers as well. Hard-disks store sectors of 512 bytes or more. Unix filesystems group sectors in larger blocks that can contain data or `inodes` representing the structure of the filesystem. Finally, applications manipulate files and directories that are translated in blocks, sectors and eventually bits by the operating system.
0/12000 · 1200
41
../../principles/reliability.rst:184
English
Computer networks use a similar approach. Each layer provides a service that is built above the underlying layer and is closer to the needs of the applications. The datalink layer builds upon the service provided by the physical layer. We will see that it also contains several functions.
0/2880 · 288
42
../../principles/reliability.rst:188
English
The datalink layer
0/180 · 18
44
../../principles/reliability.rst:194
English
To enable the transmission/reception of frames, the first problem to be solved is how to encode a frame as a sequence of bits, so that the receiver can easily recover the received frame despite the limitations of the physical layer.
0/2320 · 232
45
../../principles/reliability.rst:199
English
If the physical layer were perfect, the problem would be very simple. We would simply need to define how to encode each frame as a sequence of consecutive bits. The receiver would then easily be able to extract the frames from the received bits. Unfortunately, the imperfections of the physical layer make this framing problem slightly more complex. Several solutions have been proposed and are used in practice in different network technologies.
0/4460 · 446
46
../../principles/reliability.rst:202
English
Framing
0/100 · 7
47
../../principles/reliability.rst:204
English
The `framing` problem can be defined as : "`How does a sender encode frames so that the receiver can efficiently extract them from the stream of bits that it receives from the physical layer`".
0/1930 · 193
48
../../principles/reliability.rst:206
English
A first solution to this problem is to require the physical layer to remain idle for some time after the transmission of each frame. These idle periods can be detected by the receiver and serve as a marker to delineate frame boundaries. Unfortunately, this solution is not acceptable for two reasons. First, some physical layers cannot remain idle and always need to transmit bits. Second, inserting an idle period between frames decreases the maximum bit rate that can be achieved.
0/4820 · 482
49
../../principles/reliability.rst:208
English
Bit rate and bandwidth
0/220 · 22
50
../../principles/reliability.rst:210
English
Bit rate and bandwidth are often used to characterize the transmission capacity of the physical service. The original definition of `bandwidth <https://www.merriam-webster.com/dictionary/bandwidth>`_, as listed in the `Webster dictionary <https://www.merriam-webster.com/dictionary>`_ is `a range of radio frequencies which is occupied by a modulated carrier wave, which is assigned to a service, or over which a device can operate`. This definition corresponds to the characteristics of a given transmission medium or receiver. For example, the human ear is able to decode sounds in roughly the 0-20 KHz frequency range. By extension, bandwidth is also used to represent the capacity of a communication system in bits per second. For example, a Gigabit Ethernet link is theoretically capable of transporting one billion bits per second.
0/8370 · 837
51
../../principles/reliability.rst:215
English
Given that multi-symbol encodings cannot be used by all physical layers, a generic solution which can be used with any physical layer that is able to transmit and receive only bits `0` and `1` is required. This generic solution is called `stuffing` and two variants exist : `bit stuffing` and `character stuffing`. To enable a receiver to easily delineate the frame boundaries, these two techniques reserve special bit strings as frame boundary markers and encode the frames so that these special bit strings do not appear inside the frames.
0/5410 · 541
52
../../principles/reliability.rst:217
English
`Bit stuffing` reserves the `01111110` bit string as the frame boundary marker and ensures that there will never be six consecutive `1` symbols transmitted by the physical layer inside a frame. With bit stuffing, a frame is sent as follows. First, the sender transmits the marker, i.e. `01111110`. Then, it sends all the bits of the frame and inserts an additional bit set to `0` after each sequence of five consecutive `1` bits. This ensures that the sent frame never contains a sequence of six consecutive bits set to `1`. As a consequence, the marker pattern cannot appear inside the frame sent. The marker is also sent to mark the end of the frame. The receiver performs the opposite to decode a received frame. It first detects the beginning of the frame thanks to the `01111110` marker. Then, it processes the received bits and counts the number of consecutive bits set to `1`. If a `0` follows five consecutive bits set to `1`, this bit is removed since it was inserted by the sender. If a `1` follows five consecutive bits sets to `1`, it indicates a marker if it is followed by a bit set to `0`. The table below illustrates the application of bit stuffing to some frames.
0/11800 · 1180