Exit Zen
109
../../protocols/ethernet.rst:395
English
During the computation of the spanning tree, switches discard all received data frames, as at that time the network topology is not guaranteed to be loop-free. Once that topology has been stable for some time, the switches again start to use the MAC learning algorithm to forward data frames. Only the `Root` and `Designated` ports are used to forward data frames. Switches discard all the data frames received on their `Blocked` ports and never forward frames on these ports.
0/4760 · 476
110
../../protocols/ethernet.rst:397
English
Switches, ports and links can fail in a switched Ethernet network. When a failure occurs, the switches must be able to recompute the spanning tree to recover from the failure. The `Spanning Tree Protocol` relies on regular transmissions of the `BPDUs` to detect these failures. A `BPDU` contains two additional fields : the `Age` of the `BPDU` and the `Maximum Age`. The `Age` contains the amount of time that has passed since the root switch initially originated the `BPDU`. The root switch sends its `BPDU` with an `Age` of zero and each switch that computes its own `BPDU` increments its `Age` by one. The `Age` of the `BPDUs` stored on a switch's table is also incremented every second. A `BPDU` expires when its `Age` reaches the `Maximum Age`. When the network is stable, this does not happen as `BPDU` s are regularly sent by the `root` switch and downstream switches. However, if the `root` fails or the network becomes partitioned, `BPDU` will expire and switches will recompute their own `BPDU` and restart the `Spanning Tree Protocol`. Once a topology change has been detected, the forwarding of the data frames stops as the topology is not guaranteed to be loop-free. Additional details about the reaction to failures may be found in [IEEE802.1d]_.
0/12600 · 1260
111
../../protocols/ethernet.rst:402
English
Virtual LANs
0/120 · 12
112
../../protocols/ethernet.rst:404
English
Another important advantage of Ethernet switches is the ability to create Virtual Local Area Networks (VLANs). A virtual LAN can be defined as a `set of ports attached to one or more Ethernet switches`. A switch can support several VLANs and it runs one MAC learning algorithm for each Virtual LAN. When a switch receives a frame with an unknown or a multicast destination, it forwards it over all the ports that belong to the same Virtual LAN but not over the ports that belong to other Virtual LANs. Similarly, when a switch learns a source address on a port, it associates it to the Virtual LAN of this port and uses this information only when forwarding frames on this Virtual LAN.
0/6850 · 685
113
../../protocols/ethernet.rst:406
English
The figure below illustrates a switched Ethernet network with three Virtual LANs. `VLAN2` and `VLAN3` only require a local configuration of switch `S1`. Host `C` can exchange frames with host `D`, but not with hosts that are outside of its VLAN. `VLAN1` is more complex as there are ports of this VLAN on several switches. To support such VLANs, local configuration is not sufficient anymore. When a switch receives a frame from another switch, it must be able to determine the VLAN in which the frame originated to use the correct MAC table to forward the frame. This is done by assigning an identifier to each Virtual LAN and placing this identifier inside the headers of the frames that are exchanged between switches.
0/7210 · 721
114
../../protocols/ethernet.rst:413
English
Virtual Local Area Networks in a switched Ethernet network
0/580 · 58
115
../../protocols/ethernet.rst:415
English
IEEE defined in the [IEEE802.1q]_ standard a special header to encode the VLAN identifiers. This 32 bit header includes a 12 bit VLAN field that contains the VLAN identifier of each frame. The format of the [IEEE802.1q]_ header is described below.
0/2470 · 247
116
../../protocols/ethernet.rst:421
English
Format of the 802.1q header
0/270 · 27
117
../../protocols/ethernet.rst:423
English
The [IEEE802.1q]_ header is inserted immediately after the source MAC address in the Ethernet frame (i.e. before the EtherType field). The maximum frame size is increased by 4 bytes. It is encoded in 32 bits and contains four fields. The Tag Protocol Identifier is set to `0x8100` to allow the receiver to detect the presence of this additional header. The `Priority Code Point` (PCP) is a three bit field that is used to support different transmission priorities for the frame. Value `0` is the lowest priority and value `7` the highest. Frames with a higher priority can expect to be forwarded earlier than frames having a lower priority. The `C` bit is used for compatibility between Ethernet and Token Ring networks. The last 12 bits of the 802.1q header contain the VLAN identifier. Value `0` indicates that the frame does not belong to any VLAN while value `0xFFF` is reserved. This implies that 4094 different VLAN identifiers can be used in an Ethernet network.
0/9690 · 969
The translation has come to an end.