Exit Zen
16
../../protocols/ethernet.rst:96
English
delivers frames to their destination with a very high probability of successful delivery
0/880 · 88
17
../../protocols/ethernet.rst:97
English
does not reorder the transmitted frames
0/390 · 39
18
../../protocols/ethernet.rst:99
English
The first property is a consequence of the utilization of CSMA/CD. The second property is a consequence of the physical organization of the Ethernet network as a shared bus. These two properties are important and all revisions to the Ethernet technology have preserved them.
0/2740 · 274
19
../../protocols/ethernet.rst:109
English
Several physical layers have been defined for Ethernet networks. The first physical layer, usually called 10Base5, provided 10 Mbps over a thick coaxial cable. The characteristics of the cable and the transceivers that were used then enabled the utilization of 500 meter long segments. A 10Base5 network can also include repeaters between segments.
0/3480 · 348
20
../../protocols/ethernet.rst:113
English
The second physical layer was 10Base2. This physical layer used a thin coaxial cable that was easier to install than the 10Base5 cable, but could not be longer than 185 meters. A 10BaseF physical layer was also defined to transport Ethernet over point-to-point optical links. The major change to the physical layer was the support of twisted pairs in the 10BaseT specification. Twisted pair cables are traditionally used to support the telephone service in office buildings. Most office buildings today are equipped with structured cabling. Several twisted pair cables are installed between any room and a central telecom closet per building or per floor in large buildings. These telecom closets act as concentration points for the telephone service but also for LANs.
0/7690 · 769
21
../../protocols/ethernet.rst:118
English
The introduction of the twisted pairs led to two major changes to Ethernet. The first change concerns the physical topology of the network. 10Base2 and 10Base5 networks are shared buses, the coaxial cable typically passes through each room that contains a connected computer. A 10BaseT network is a star-shaped network. All the devices connected to the network are attached to a twisted pair cable that ends in the telecom closet. From a maintenance perspective, this is a major improvement. The cable is a weak point in 10Base2 and 10Base5 networks. Any physical damage on the cable broke the entire network and when such a failure occurred, the network administrator had to manually check the entire cable to detect where it was damaged. With 10BaseT, when one twisted pair is damaged, only the device connected to this twisted pair is affected and this does not affect the other devices. The second major change introduced by 10BaseT was that is was impossible to build a 10BaseT network by simply connecting all the twisted pairs together. All the twisted pairs must be connected to a relay that operates in the physical layer. This relay is called an `Ethernet hub`. A `hub` is thus a physical layer relay that receives an electrical signal on one of its interfaces, regenerates the signal and transmits it over all its other interfaces. Some `hubs` are also able to convert the electrical signal from one physical layer to another (e.g. 10BaseT to 10Base2 conversion).
0/14740 · 1474
22
../../protocols/ethernet.rst:149
English
Computers can directly be attached to Ethernet hubs. Ethernet hubs themselves can be attached to other Ethernet hubs to build a larger network. However, some important guidelines must be followed when building a complex network with hubs. First, the network topology must be a tree. As hubs are relays in the physical layer, adding a link between `Hub2` and `Hub3` in the network below would create an electrical shortcut that would completely disrupt the network. This implies that there cannot be any redundancy in a hub-based network. A failure of a hub or of a link between two hubs would partition the network into two isolated networks. Second, as hubs are relays in the physical layer, collisions can happen and must be handled by CSMA/CD as in a 10Base5 network. This implies that the maximum delay between any pair of devices in the network cannot be longer than the 51.2 microseconds `slot time`. If the delay is longer, collisions between short frames may not be correctly detected. This constraint limits the geographical spread of 10BaseT networks containing hubs.
0/10770 · 1077
23
../../protocols/ethernet.rst:156
English
A hierarchical Ethernet network composed of hubs
0/480 · 48
24
../../protocols/ethernet.rst:162
English
In the late 1980s, 10 Mbps became too slow for some applications and network manufacturers developed several LAN technologies that offered higher bandwidth, such as the 100 Mbps FDDI LAN that used optical fibers. As the development of 10Base5, 10Base2 and 10BaseT had shown that Ethernet could be adapted to different physical layers, several manufacturers started to work on 100 Mbps Ethernet and convinced IEEE to standardize this new technology that was initially called `Fast Ethernet`. `Fast Ethernet` was designed under two constraints. First, `Fast Ethernet` had to support twisted pairs. Although it was easier from a physical layer perspective to support higher bandwidth on coaxial cables than on twisted pairs, coaxial cables were a nightmare from deployment and maintenance perspectives. Second, `Fast Ethernet` had to be perfectly compatible with the existing 10 Mbps Ethernet to allow `Fast Ethernet` technology to be used initially as a backbone technology to interconnect 10 Mbps Ethernet networks. This forced `Fast Ethernet` to use exactly the same frame format as 10 Mbps Ethernet. This implied that the minimum `Fast Ethernet` frame size remained at 512 bits. To preserve CSMA/CD with this minimum frame size and 100 Mbps instead of 10 Mbps, the duration of the `slot time` was decreased to 5.12 microseconds.
0/13290 · 1329
25
../../protocols/ethernet.rst:164
English
The evolution of Ethernet did not stop. In 1998, the IEEE published a first standard to provide Gigabit Ethernet over optical fibers. Several other types of physical layers were added afterwards. The `10 Gigabit Ethernet <http://en.wikipedia.org/wiki/10_gigabit_Ethernet>`_ standard appeared in 2002. Work is ongoing to develop `standards <http://www.ieee802.org/3/ba/public/index.html>`_ for 40 Gigabit and 100 Gigabit Ethernet and some are thinking about `Terabit Ethernet <http://www.networkworld.com/news/2009/042009-terabit-ethernet.html>`_. The table below lists the main Ethernet standards. A more detailed list may be found at http://en.wikipedia.org/wiki/Ethernet_physical_layer.
0/6880 · 688
26
../../protocols/ethernet.rst:169
English
Standard
0/100 · 8
27
../../protocols/ethernet.rst:169
English
Comments
0/100 · 8
28
../../protocols/ethernet.rst:171
English
10Base5
0/100 · 7
29
../../protocols/ethernet.rst:171
English
Thick coaxial cable, 500m
0/250 · 25
30
../../protocols/ethernet.rst:172
English
10Base2
0/100 · 7
31
../../protocols/ethernet.rst:172
English
Thin coaxial cable, 185m
0/240 · 24
32
../../protocols/ethernet.rst:173
English
10BaseT
0/100 · 7
33
../../protocols/ethernet.rst:173
English
Two pairs of category 3+ UTP
0/280 · 28
34
../../protocols/ethernet.rst:174
English
10Base-F
0/100 · 8
35
../../protocols/ethernet.rst:174
English
10 Mb/s over optical fiber
0/260 · 26