Exit Zen
93
../../protocols/ethernet.rst:366
English
Otherwise, the switch chooses the best priority vector from its table, `bv = <R,c+cost[q'],T,p,q'>`. The port `q'`, over which this best root priority vector was learned, is the switch port that is closest to the `root` switch. This port becomes the `Root` port of the switch. There is only one `Root` port per switch (except for the `Root` switches whose ports are all `Designated`). The switch can then compute its own `BPDU` as `BPDU = <R,c',S,p>` , where `R` is the `root identifier`, `c'` the cost of the best root priority vector, `S` the identifier of the switch and `p` will be replaced by the number of the port over which the `BPDU` will be sent.
0/6560 · 656
94
../../protocols/ethernet.rst:368
English
To determine the state of its other ports, the switch compares its own `BPDU` with the last `BPDU` received on each port. Note that the comparison is done by using the `BPDUs` and not the `root priority vectors`. If the switch's `BPDU` is better than the last `BPDU` of this port, the port becomes a `Designated` port. Otherwise, the port becomes a `Blocked` port.
0/3640 · 364
95
../../protocols/ethernet.rst:370
English
The state of each port is important when considering the transmission of `BPDUs`. The root switch regularly sends its own `BPDU` over all of its (`Designated`) ports. This `BPDU` is received on the `Root` port of all the switches that are directly connected to the `root switch`. Each of these switches computes its own `BPDU` and sends this `BPDU` over all its `Designated` ports. These `BPDUs` are then received on the `Root` port of downstream switches, which then compute their own `BPDU`, etc. When the network topology is stable, switches send their own `BPDU` on all their `Designated` ports, once they receive a `BPDU` on their `Root` port. No `BPDU` is sent on a `Blocked` port. Switches listen for `BPDUs` on their `Blocked` and `Designated` ports, but no `BPDU` should be received over these ports when the topology is stable. The utilization of the ports for both `BPDUs` and data frames is summarized in the table below.
0/9330 · 933
96
../../protocols/ethernet.rst:373
English
Port state
0/100 · 10
97
../../protocols/ethernet.rst:373
English
Receives BPDUs
0/140 · 14
98
../../protocols/ethernet.rst:373
English
Sends BPDU
0/100 · 10
99
../../protocols/ethernet.rst:373
English
Handles data frames
0/190 · 19
100
../../protocols/ethernet.rst:375
English
Blocked
0/100 · 7
101
../../protocols/ethernet.rst:375 • ../../protocols/ethernet.rst:376 • ../../protocols/ethernet.rst:376 • ../../protocols/ethernet.rst:377 • ../../protocols/ethernet.rst:377 • ../../protocols/ethernet.rst:377
English
yes
0/100 · 3
102
../../protocols/ethernet.rst:375 • ../../protocols/ethernet.rst:375 • ../../protocols/ethernet.rst:376
English
no
0/100 · 2
103
../../protocols/ethernet.rst:376
English
Root
0/100 · 4
104
../../protocols/ethernet.rst:377
English
Designated
0/100 · 10
105
../../protocols/ethernet.rst:382
English
To illustrate the operation of the `Spanning Tree Protocol`, let us consider the simple network topology in the figure below.
0/1250 · 125
106
../../protocols/ethernet.rst:389
English
A simple Spanning tree computed in a switched Ethernet network
0/620 · 62
107
../../protocols/ethernet.rst:391
English
Assume that `Switch4` is the first to boot. It sends its own `BPDU = <4,0,4,1>` (resp. `BPDU = <4,0,4,2>`) on port 1 (resp. port 2). When `Switch1` boots, it sends `BPDU = <1,0,1,1>`. This `BPDU` is received by `Switch4`, which updates its `BPDU` and root priority vector tables and computes a new `BPDU = <1,3,4,1>` (resp. `BPDU = <1,3,4,2>`) on port 1 (resp. port 2). Indeed, there is only one root priority vector and hence, it is the best one. Port 1 of `Switch4` becomes the `Root` port while its second port is still in the `Designated` state.
0/5490 · 549
108
../../protocols/ethernet.rst:393
English
Assume now that `Switch9` boots and immediately receives `Switch1` 's `BPDU` on port 1. `Switch9` computes its own `BPDU = <1,1,9,1>` (resp. `BPDU = <1,1,9,2>`) on port 1 (resp. port 2) and port 1 becomes the `Root` port of this switch. The `BPDU` is sent on port 2 of `Switch9` and reaches `Switch4`. `Switch4` compares the priority vectors. It notices that the last computed vector (i.e., `V[2] = <1,2,9,2,2>`) is better than `V[1] = <1,3,1,1,1>`. Thus, `Switch4`'s `BPDU` is recomputed and port 2 becomes the `Root` port of `Switch4`. `Switch4` compares its new `BPDU = <1,2,4,p>` with the last `BPDU` received on each port (except for the `Root` port). Port 1 becomes a `Blocked` port on `Switch4` because the `BPDU=<1,0,1,1>` received on this port is better.
0/7630 · 763
109
../../protocols/ethernet.rst:395
English
During the computation of the spanning tree, switches discard all received data frames, as at that time the network topology is not guaranteed to be loop-free. Once that topology has been stable for some time, the switches again start to use the MAC learning algorithm to forward data frames. Only the `Root` and `Designated` ports are used to forward data frames. Switches discard all the data frames received on their `Blocked` ports and never forward frames on these ports.
0/4760 · 476
110
../../protocols/ethernet.rst:397
English
Switches, ports and links can fail in a switched Ethernet network. When a failure occurs, the switches must be able to recompute the spanning tree to recover from the failure. The `Spanning Tree Protocol` relies on regular transmissions of the `BPDUs` to detect these failures. A `BPDU` contains two additional fields : the `Age` of the `BPDU` and the `Maximum Age`. The `Age` contains the amount of time that has passed since the root switch initially originated the `BPDU`. The root switch sends its `BPDU` with an `Age` of zero and each switch that computes its own `BPDU` increments its `Age` by one. The `Age` of the `BPDUs` stored on a switch's table is also incremented every second. A `BPDU` expires when its `Age` reaches the `Maximum Age`. When the network is stable, this does not happen as `BPDU` s are regularly sent by the `root` switch and downstream switches. However, if the `root` fails or the network becomes partitioned, `BPDU` will expire and switches will recompute their own `BPDU` and restart the `Spanning Tree Protocol`. Once a topology change has been detected, the forwarding of the data frames stops as the topology is not guaranteed to be loop-free. Additional details about the reaction to failures may be found in [IEEE802.1d]_.
0/12600 · 1260
111
../../protocols/ethernet.rst:402
English
Virtual LANs
0/120 · 12
112
../../protocols/ethernet.rst:404
English
Another important advantage of Ethernet switches is the ability to create Virtual Local Area Networks (VLANs). A virtual LAN can be defined as a `set of ports attached to one or more Ethernet switches`. A switch can support several VLANs and it runs one MAC learning algorithm for each Virtual LAN. When a switch receives a frame with an unknown or a multicast destination, it forwards it over all the ports that belong to the same Virtual LAN but not over the ports that belong to other Virtual LANs. Similarly, when a switch learns a source address on a port, it associates it to the Virtual LAN of this port and uses this information only when forwarding frames on this Virtual LAN.
0/6850 · 685