cnp3-ebook/protocols/ipv6 — English @ Weblate

Exit Zen

192 ../../protocols/ipv6.rst:680

	English A MAC address 13/10000 · 13
193 ../../protocols/ipv6.rst:682

	English MAC addresses are allocated in blocks of :math:`2^{20}`. When a company registers for a block of MAC addresses, it receives an identifier. company identifier is then used to populated the `c` bits of the MAC addresses. The company can allocate all addresses in starting with this prefix and manages the `m` bits as it wishes. 325/10000 · 325
194 ../../protocols/ipv6.rst:687

	English A MAC address converted into a 64 bits host identifier 54/10000 · 54
195 ../../protocols/ipv6.rst:689

	English Inside a MAC address, the two bits indicated as `0` and `g` in the figure above play a special role. The first bit indicates whether the address is universal or local. The `g` bit indicates whether this is a multicast address or a unicast address. The MAC address can be converted into a 64 bits host identifier by flipping the value of the `0` bit and inserting ``FFFE``, i.e. ``1111111111111110`` in binary, in the middle of the address as shown in the figure below. The `c`, `m` and `g` bits of the MAC address are not modified. 531/10000 · 531
196 ../../protocols/ipv6.rst:692

	English The next step is to connect the LAN to the Internet. For this, a router is attached to the LAN. 95/10000 · 95
197 ../../protocols/ipv6.rst:711

	English Assume that the LAN containing the two hosts and the router is assigned prefix ``2001:db8:1234:5678/64``. A first solution to configure the IPv6 addresses in this network is to assign them manually. A possible assignment is : 225/10000 · 225
198 ../../protocols/ipv6.rst:713

	English ``2001:db8:1234:5678::1`` is assigned to ``router`` 51/10000 · 51
199 ../../protocols/ipv6.rst:714

	English ``2001:db8:1234:5678::AA`` is assigned to ``hostA`` 51/10000 · 51
200 ../../protocols/ipv6.rst:715

	English ``2001:db8:1234:5678::BB`` is assigned to ``hostB`` 51/10000 · 51
201 ../../protocols/ipv6.rst:719

	English To be able to exchange IPv6 packets with ``hostB``, ``hostA`` needs to know the MAC address of the interface of ``hostB`` on the LAN. This is the `address resolution` problem. In IPv6, this problem is solved by using the Neighbor Discovery Protocol (NDP). NDP is specified in :rfc:`4861`. This protocol is part of ICMPv6 and uses the multicast datalink layer service. 367/10000 · 367
202 ../../protocols/ipv6.rst:727

	English NDP allows a host to discover the MAC address used by any other host attached to the same LAN. NDP operates in two steps. First, the querier sends a multicast ICMPv6 Neighbor Solicitation message that contains as parameter the queried IPv6 address. This multicast ICMPv6 NS is placed inside a multicast frame [#fndpmulti]_. The queried node receives the frame, parses it and replies with a unicast ICMPv6 Neighbor Advertisement that provides its own IPv6 and MAC addresses. Upon reception of the Neighbor Advertisement message, the querier stores the mapping between the IPv6 and the MAC address inside its NDP table. This table is a data structure that maintains a cache of the recently received Neighbor Advertisement. Thanks to this cache, a host only needs to send a Neighbor Solicitation message for the first packet that it sends to a given host. After this initial packet, the NDP table can provide the mapping between the destination IPv6 address and the corresponding MAC address. 989/10000 · 989
203 ../../protocols/ipv6.rst:738

	English The NS message can also be used to verify the reachability of a host in the local subnet. For this usage, NS messages can be sent in unicast since other nodes on the subnet do not need to process the message. 208/10000 · 208
204 ../../protocols/ipv6.rst:740

	English When an entry in the NDP table times out on a host, it may either be deleted or the host may try to validate it by sending the NS message again. 144/10000 · 144
205 ../../protocols/ipv6.rst:747

	English This is not the only usage of the Neighbor Solicitation and Neighbor Advertisement messages. They are also used to detect the utilization of duplicate addresses. In the network above, consider what happens when a new host is connected to the LAN. If this host is configured by mistake with the same address as ``hostA`` (i.e. ``2001:db8:1234:5678::AA``), problems could occur. Indeed, if two hosts have the same IPv6 address on the LAN, but different MAC addresses, it will be difficult to correctly reach them. IPv6 anticipated this problem and includes a `Duplicate Address Detection` Algorithm (DAD). When an IPv6 address [#flinklocal]_ is configured on a host, by any means, the host must verify the uniqueness of this address on the LAN. For this, it multicasts an ICMPv6 Neighbor Solicitation that queries the network for its newly configured address. The IPv6 source address of this NS is set to ``::`` (i.e. the reserved unassigned address) if the host does not already have an IPv6 address on this subnet). If the NS does not receive any answer, the new address is considered to be unique and can safely be used. Otherwise, the new address is refused and an error message should be returned to the system administrator or a new IPv6 address should be generated. The `Duplicate Address Detection` Algorithm can prevent various operational problems that are often difficult to debug. 1390/10000 · 1390
206 ../../protocols/ipv6.rst:753

	English Few users manually configure the IPv6 addresses on their hosts. They prefer to rely on protocols that can automatically configure their IPv6 addresses. IPv6 supports two such protocols : DHCPv6 and the Stateless Address Autoconfiguration (SLAAC). 246/10000 · 246
207 ../../protocols/ipv6.rst:764

	English The Stateless Address Autoconfiguration (SLAAC) mechanism defined in :rfc:`4862` enables hosts to automatically configure their addresses without maintaining any state. When a host boots, it derives its identifier from its datalink layer address [#fprivacy]_ as explained earlier and concatenates this 64 bits identifier to the `FE80::/64` prefix to obtain its link-local IPv6 address. It then multicasts a Neighbor Solicitation with its link-local address as a target to verify whether another host is using the same link-local address on this subnet. If it receives a Neighbor Advertisement indicating that the link-local address is used by another host, it generates another 64 bits identifier and sends again a Neighbor Solicitation. If there is no answer, the host considers its link-local address to be valid. This address will be used as the source address for all NDP messages sent on the subnet. 904/10000 · 904
208 ../../protocols/ipv6.rst:766

	English To automatically configure its global IPv6 address, the host must know the globally routable IPv6 prefix that is used on the local subnet. IPv6 routers regularly multicast ICMPv6 Router Advertisement messages that indicate the IPv6 prefix assigned to the subnet. The Router Advertisement message contains several interesting fields. 332/10000 · 332
209 ../../protocols/ipv6.rst:772

	English Format of the ICMPv6 Router Advertisement message 49/10000 · 49
210 ../../protocols/ipv6.rst:774

	English This message is sent from the link-local address of the router on the subnet. Its destination is the IPv6 multicast address that targets all IPv6 enabled hosts (i.e. ``ff02::1``). The `Cur Hop Limit` field, if different from zero, allows specifying the default `Hop Limit` that hosts should use when sending IPv6 packets from this subnet. ``64`` is a frequently used value. The `M` and `O` bits are used to indicate that some information can be obtained from DHCPv6. The `Router Lifetime` parameter provides the expected lifetime (in seconds) of the sending router acting as a default router. This lifetime enables planning the replacement of a router by another one in the same subnet. The `Reachable Time` and the `Retrans Timer` parameter are used to configure the utilization of the NDP protocol on the hosts attached to the subnet. 836/10000 · 836
211 ../../protocols/ipv6.rst:776

	English Several options can be included in the Router Advertisement message. The simplest one is the MTU option that indicates the MTU to be used within the subnet. Thanks to this option, it is possible to ensure that all devices attached to the same subnet use the same MTU. Otherwise, operational problems could occur. The `Prefix` option is more important. It provides information about the prefix(es) that is (are) advertised by the router on the subnet. 450/10000 · 450

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.