cnp3-ebook/protocols/ipv6 — English @ Weblate

Exit Zen

210 ../../protocols/ipv6.rst:774

	English This message is sent from the link-local address of the router on the subnet. Its destination is the IPv6 multicast address that targets all IPv6 enabled hosts (i.e. ``ff02::1``). The `Cur Hop Limit` field, if different from zero, allows specifying the default `Hop Limit` that hosts should use when sending IPv6 packets from this subnet. ``64`` is a frequently used value. The `M` and `O` bits are used to indicate that some information can be obtained from DHCPv6. The `Router Lifetime` parameter provides the expected lifetime (in seconds) of the sending router acting as a default router. This lifetime enables planning the replacement of a router by another one in the same subnet. The `Reachable Time` and the `Retrans Timer` parameter are used to configure the utilization of the NDP protocol on the hosts attached to the subnet. 836/10000 · 836
211 ../../protocols/ipv6.rst:776

	English Several options can be included in the Router Advertisement message. The simplest one is the MTU option that indicates the MTU to be used within the subnet. Thanks to this option, it is possible to ensure that all devices attached to the same subnet use the same MTU. Otherwise, operational problems could occur. The `Prefix` option is more important. It provides information about the prefix(es) that is (are) advertised by the router on the subnet. 450/10000 · 450
212 ../../protocols/ipv6.rst:782

	English The Prefix information option 29/10000 · 29
213 ../../protocols/ipv6.rst:787

	English The key information placed in this option are the prefix and its length. This allows the hosts attached to the subnet to automatically configure their own IPv6 address. The `Valid` and `Preferred` `Lifetimes` provide information about the expected lifetime of the prefixes. Associating some time validity to prefixes is a good practice from an operational viewpoint. There are some situations where the prefix assigned to a subnet needs to change without impacting the hosts attached to the subnet. This is often called the IPv6 renumbering problem in the literature :rfc:`7010`. A very simple scenario is the following. An SME subscribes to one ISP. Its router is attached to another router of this ISP and advertises a prefix assigned by the ISP. The SME is composed of a single subnet and all its hosts rely on stateless address configuration. After a few years, the SME decides to change of network provider. It connects its router to the second ISP and receives a different prefix from this ISP. At this point, two prefixes are advertised on the SME's subnet. The old prefix can be advertised with a short lifetime to ensure that hosts will stop using it while the new one is advertised with a longer lifetime. After sometime, the router stops advertising the old prefix and the hosts stop using it. The old prefix can now be returned back to the first ISP. In larger networks, renumbering an IPv6 remains a difficult operational problem [LeB2009]_. 1454/10000 · 1454
214 ../../protocols/ipv6.rst:789

	English Upon reception of this message, the host can derive its global IPv6 address by concatenating its 64 bits identifier with the received prefix. It concludes the SLAAC by sending a Neighbor Solicitation message targeted at its global IPv6 address to ensure that no other host is using the same IPv6 address. 304/10000 · 304
215 ../../protocols/ipv6.rst:791

	English Router Advertisements and Hop Limits 36/10000 · 36
216 ../../protocols/ipv6.rst:793

	English ICMPv6 Router Advertisements messages are regularly sent by routers. They are destined to all devices attached to the local subnet and no router should ever forward them to another subnet. Still, these messages are sent inside IPv6 packets whose `Hop Limit` is always set to ``255``. Given that the packet should not be forwarded outside of the local subnet, the reader could expect instead a `Hop Limit` set to ``1``. Using a `Hop Limit` set to ``255`` provides one important benefit from a security viewpoint and this hack has been adapted in several Internet protocols. When a host receives a `Router Advertisement` message, it expects that this message has been generated by a router attached to the same subnet. Using a `Hop Limit` of ``255`` provides a simple check for this. If the message was generated by an attacker outside the subnet, it would reach the subnet with a decremented `Hop Limit`. Checking that the `Hop Limit` is set to ``255`` is a simple [#fsend]_ verification that the packet was generated on this particular subnet. :rfc:`5082` provides other examples of protocols that use this hack and discuss its limitations. 1140/10000 · 1140
217 ../../protocols/ipv6.rst:796

	English Routers regularly send Router Advertisement messages. These messages are triggered by a timer that is often set at approximately 30 seconds. Usually, hosts wait for the arrival of a Router Advertisement message to configure their address. This implies that hosts could sometimes need to wait 30 seconds before being able to configure their address. If this delay is too long, a host can also send a `Router Solicitation` message. This message is sent towards the multicast address that corresponds to all IPv6 routers (i.e. ``FF01::2``) and the default router will reply. 571/10000 · 571
218 ../../protocols/ipv6.rst:798

	English The last point that needs to be explained about ICMPv6 is the `Redirect` message. This message is used when there is more than one router on a subnet as shown in the figure below. 179/10000 · 179
219 ../../protocols/ipv6.rst:819

	English In this network, ``router1`` is the default router for all hosts. The second router, ``router2`` provides connectivity to a specific IPv6 subnet, e.g. ``2001:db8:abcd::/48``. These two routers attached to the same subnet can be used in different ways. First, it is possible to manually configure the routing tables on all hosts to add a route towards ``2001:db8:abcd::/48`` via ``router2``. Unfortunately, forcing such manual configuration boils down all the benefits of using address auto-configuration in IPv6. The second approach is to automatically configure a default route via ``router1`` on all hosts. With such route, when a host needs to send a packet to any address within ``2001:db8:abcd::/48``, it will send it to ``router1``. ``router1`` would consult its routing table and find that the packet needs to be sent again on the subnet to reach ``router2``. This is a waste of time. A better approach would be to enable the hosts to automatically learn the new route. This is possible thanks to the ICMPv6 `Redirect` message. When ``router1`` receives a packet that needs to be forwarded back on the same interface, it replies with a `Redirect` message that indicates that the packet should have been sent via ``router2``. Upon reception of a `Redirect` message, the host updates it forwarding table to include a new transient entry for the destination reported in the message. A timeout is usually associated with this transient entry to automatically delete it after some time. 1490/10000 · 1490
220 ../../protocols/ipv6.rst:826

	English An alternative is the Dynamic Host Configuration Protocol (DHCP) defined in :rfc:`2131` and :rfc:`3315`. DHCP allows a host to automatically retrieve its assigned IPv6 address, but relies on server. A DHCP server is associated to each subnet [#fdhcpserver]_. Each DHCP server manages a pool of IPv6 addresses assigned to the subnet. When a host is first attached to the subnet, it sends a DHCP request message in a UDP segment (the DHCP server listens on port 67). As the host knows neither its IPv6 address nor the IPv6 address of the DHCP server, this UDP segment is sent inside a multicast packet target at the DHCP servers. The DHCP request may contain various options such as the name of the host, its datalink layer address, etc. The server captures the DHCP request and selects an unassigned address in its address pool. It then sends the assigned IPv6 address in a DHCP reply message which contains the datalink layer address of the host and additional information such as the subnet mask, the address of the default router or the address of the DNS resolver. The DHCP reply also specifies the lifetime of the address allocation. This forces the host to renew its address allocation once it expires. Thanks to the limited lease time, IP addresses are automatically returned to the pool of addresses when hosts are powered off. 1336/10000 · 1336
221 ../../protocols/ipv6.rst:828

	English Both SLAAC and DHCPv6 can be extended to provide additional information beyond the IPv6 prefix/address. For example, :rfc:`6106` defines options for the ICMPv6 ND message that can carry the IPv6 address of the recursive DNS resolver and a list of default domain search suffixes. It is also possible to combine SLAAC with DHCPv6. :rfc:`3736` defines a stateless variant of DHCPv6 that can be used to distribute DNS information while SLAAC is used to distribute the prefixes. 473/10000 · 473
222 ../../protocols/ipv6.rst:834

	English Footnotes 9/10000 · 9
223 ../../protocols/ipv6.rst:835

	English The full list of allocated IPv6 multicast addresses is available at http://www.iana.org/assignments/ipv6-multicast-addresses 124/10000 · 124
224 ../../protocols/ipv6.rst:837

	English The IANA_ maintains the list of all allocated Next Header types at http://www.iana.org/assignments/protocol-numbers/ 116/10000 · 116
225 ../../protocols/ipv6.rst:839

	English When IPv4 was designed, the situation was different. The IPv4 header includes a checksum that only covers the network header. This checksum is computed by the source and updated by all intermediate routers that decrement the TTL, which is the IPv4 equivalent of the `HopLimit` used by IPv6. 290/10000 · 290
226 ../../protocols/ipv6.rst:841

	English Until a few years ago, all hosts replied to `Echo request` ICMP messages. However, due to the security problems that have affected TCP/IP implementations, many of these implementations can now be configured to disable answering `Echo request` ICMP messages. 257/10000 · 257
227 ../../protocols/ipv6.rst:843

	English For a discussion of the issues with the router alert IP option, see http://tools.ietf.org/html/draft-rahman-rtg-router-alert-dangerous-00 or http://tools.ietf.org/html/draft-rahman-rtg-router-alert-considerations-03 215/10000 · 215
228 ../../protocols/ipv6.rst:846

	English For simplicity, you assume that each datalink layer interface is assigned a 64 bits MAC address. As we will see later, today's datalink layer technologies mainly use 48 bits MAC addresses, but the smaller addresses can easily be converted into 64 bits addresses. 262/10000 · 262
229 ../../protocols/ipv6.rst:848

	English :rfc:`4291` and :rfc:`4861` explain in more details how the IPv6 multicast address is determined from the target IPv6 unicast address. These details are outside the scope of this book, but may matter if you try to understand a packet trace. 240/10000 · 240

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.