Exit Zen
148
../../protocols/tcp.rst:447
English
The default go-back-n retransmission strategy was defined in :rfc:`793`. When the retransmission timer expires, TCP retransmits the first unacknowledged segment (i.e. the one having sequence number `snd.una`). After each expiration of the retransmission timeout, :rfc:`2988` recommends to double the value of the retransmission timeout. This is called an `exponential backoff`. This doubling of the retransmission timeout after a retransmission was included in TCP to deal with issues such as network/receiver overload and incorrect initial estimations of the retransmission timeout. If the same segment is retransmitted several times, the retransmission timeout is doubled after every retransmission until it reaches a configured maximum. :rfc:`2988` suggests a maximum retransmission timeout of at least 60 seconds. Once the retransmission timeout reaches this configured maximum, the remote host is considered to be unreachable and the TCP connection is closed.
0/9640 · 964
149
../../protocols/tcp.rst:452
English
This retransmission strategy has been refined based on the experience of using TCP on the Internet. The first refinement was a clarification of the strategy used to send acknowledgments. As TCP uses piggybacking, the easiest and less costly method to send acknowledgments is to place them in the data segments sent in the other direction. However, few application layer protocols exchange data in both directions at the same time and thus this method rarely works. For an application that is sending data segments in one direction only, the remote TCP entity returns empty TCP segments whose only useful information is their acknowledgment number. This may cause a large overhead in wide area network if a pure `ACK` segment is sent in response to each received data segment. Most TCP implementations use a `delayed acknowledgment` strategy. This strategy ensures that piggybacking is used whenever possible, otherwise pure `ACK` segments are sent for every second received data segments when there are no losses. When there are losses or reordering, `ACK` segments are more important for the sender and they are sent immediately :rfc:`813` :rfc:`1122`. This strategy relies on a new timer with a short delay (e.g. 50 milliseconds) and one additional flag in the TCB. It can be implemented as follows.
0/13010 · 1301
150
../../protocols/tcp.rst:480
English
Due to this delayed acknowledgment strategy, during a bulk transfer, a TCP implementation usually acknowledges every second TCP segment received.
0/1450 · 145
151
../../protocols/tcp.rst:482
English
The default go-back-n retransmission strategy used by TCP has the advantage of being simple to implement, in particular on the receiver side, but when there are losses, a go-back-n strategy provides a lower performance than a selective repeat strategy. The TCP developers have designed several extensions to TCP to allow it to use a selective repeat strategy while maintaining backward compatibility with older TCP implementations. These TCP extensions assume that the receiver is able to buffer the segments that it receives out-of-sequence.
0/5420 · 542
152
../../protocols/tcp.rst:486
English
The first extension that was proposed is the fast retransmit heuristic. This extension can be implemented on TCP senders and thus does not require any change to the protocol. It only assumes that the TCP receiver is able to buffer out-of-sequence segments.
0/2560 · 256
153
../../protocols/tcp.rst:488
English
From a performance point of view, one issue with TCP's `retransmission timeout` is that when there are isolated segment losses, the TCP sender often remains idle waiting for the expiration of its retransmission timeouts. Such isolated losses are frequent in the global Internet [Paxson99]_. A heuristic to deal with isolated losses without waiting for the expiration of the retransmission timeout has been included in many TCP implementations since the early 1990s. To understand this heuristic, let us consider the figure below that shows the segments exchanged over a TCP connection when an isolated segment is lost.
0/6190 · 619
154
../../protocols/tcp.rst:494
English
Detecting isolated segment losses
0/330 · 33
155
../../protocols/tcp.rst:496
English
As shown above, when an isolated segment is lost the sender receives several `duplicate acknowledgments` since the TCP receiver immediately sends a pure acknowledgment when it receives an out-of-sequence segment. A duplicate acknowledgment is an acknowledgment that contains the same `acknowledgment number` as a previous segment. A single duplicate acknowledgment does not necessarily imply that a segment was lost, as a simple reordering of the segments may cause duplicate acknowledgments as well. Measurements [Paxson99]_ have shown that segment reordering is frequent in the Internet. Based on these observations, the `fast retransmit` heuristic has been included in most TCP implementations. It can be implemented as follows.
0/7320 · 732
156
../../protocols/tcp.rst:510
English
This heuristic requires an additional variable in the TCB (`dupacks`). Most implementations set the default number of duplicate acknowledgments that trigger a retransmission to 3. It is now part of the standard TCP specification :rfc:`2581`. The `fast retransmit` heuristic improves the TCP performance provided that isolated segments are lost and the current window is large enough to allow the sender to send three duplicate acknowledgments.
0/4430 · 443
157
../../protocols/tcp.rst:512
English
The figure below illustrates the operation of the `fast retransmit` heuristic.
0/780 · 78
158
../../protocols/tcp.rst:518
English
TCP fast retransmit heuristics
0/300 · 30
159
../../protocols/tcp.rst:523
English
When losses are not isolated or when the windows are small, the performance of the `fast retransmit` heuristic decreases. In such environments, it is necessary to allow a TCP sender to use a selective repeat strategy instead of the default go-back-n strategy. Implementing selective-repeat requires a change to the TCP protocol as the receiver needs to be able to inform the sender of the out-of-order segments that it has already received. This can be done by using the Selective Acknowledgments (SACK) option defined in :rfc:`2018`. This TCP option is negotiated during the establishment of a TCP connection. If both TCP hosts support the option, SACK blocks can be attached by the receiver to the segments that it sends. SACK blocks allow a TCP receiver to indicate the blocks of data that it has received correctly but out of sequence. The figure below illustrates the utilization of the SACK blocks.
0/9040 · 904
160
../../protocols/tcp.rst:529
English
TCP selective acknowledgments
0/290 · 29
161
../../protocols/tcp.rst:531
English
A SACK option contains one or more blocks. A block corresponds to all the sequence numbers between the `left edge` and the `right edge` of the block. The two edges of the block are encoded as 32 bit numbers (the same size as the TCP sequence number) in an SACK option. As the SACK option contains one byte to encode its type and one byte for its length, a SACK option containing `b` blocks is encoded as a sequence of :math:`2+8 \times b` bytes. In practice, the size of the SACK option can be problematic as the optional TCP header extension cannot be longer than 40 bytes. As the SACK option is usually combined with the :rfc:`1323` timestamp extension, this implies that a TCP segment cannot usually contain more than three SACK blocks. This limitation implies that a TCP receiver cannot always place in the SACK option that it sends, information about all the received blocks.
0/8800 · 880
162
../../protocols/tcp.rst:533
English
To deal with the limited size of the SACK option, a TCP receiver currently having more than 3 blocks inside its receiving buffer must select the blocks to place in the SACK option. A good heuristic is to put in the SACK option the blocks that have most recently changed, as the sender is likely to be already aware of the older blocks.
0/3350 · 335
163
../../protocols/tcp.rst:535
English
When a sender receives a SACK option indicating a new block and thus a new possible segment loss, it usually does not retransmit the missing segments immediately. To deal with reordering, a TCP sender can use a heuristic similar to `fast retransmit` by retransmitting a gap only once it has received three SACK options indicating this gap. It should be noted that the SACK option does not supersede the `acknowledgment number` of the TCP header. A TCP sender can only remove data from its sending buffer once they have been acknowledged by TCP's cumulative acknowledgments. This design was chosen for two reasons. First, it allows the receiver to discard parts of its receiving buffer when it is running out of memory without loosing data. Second, as the SACK option is not transmitted reliably, the cumulative acknowledgments are still required to deal with losses of `ACK` segments carrying only SACK information. Thus, the SACK option only serves as a hint to allow the sender to optimize its retransmissions.
0/10120 · 1012
164
../../protocols/tcp.rst:537
English
As explained earlier, the TCP Timestamp option :rfc:`1323` prevents ambiguities while collecting round-trip-time measurements. It plays another very important role in today's high-bandwidth networks. Since TCP uses 32 bits long sequence numbers, the sequence numbers wrap after the transmission of 4 GBytes of data. With 10 Gbps and soon 100 Gbps interfaces, TCP only needs to transmit during a few seconds before reusing the same sequence number. Given that the Maximum Segment Lifetime is still 2 minutes, several packets, belonging to the same TCP connection could use the same sequence number. If one of these packets is severely delayed through the network, it could reappear at the same time as a packet with the same TCP sequence number. To prevent this problem, most modern TCP implementations associate a TCP timestamp option to each segment on transmission. When a TCP stack receives a TCP segment, it checks that its TCP timestamp is valid and if not the segment is discarded :rfc:`7323`.
0/9990 · 999
165
../../protocols/tcp.rst:544
English
TCP connection release
0/220 · 22
166
../../protocols/tcp.rst:548
English
TCP, like most connection-oriented transport protocols, supports two types of connection releases :
0/990 · 99
167
../../protocols/tcp.rst:550
English
graceful connection release, where each TCP user can release its own direction of data transfer after having transmitted all data
0/1290 · 129