cnp3-ebook/protocols/wifi — English @ Weblate

Exit Zen

43 ../../protocols/wifi.rst:109

	English 802.11 control frames are simpler than data frames. They contain a `Frame Control`, a `Duration` field and one or two addresses. The acknowledgment frames are very small. They only contain the address of the destination of the acknowledgment. There is no source address and no `Sequence Control` field in the acknowledgment frames. This is because the acknowledgment frame can easily be associated to the previous frame that it acknowledges. Indeed, each unicast data frame contains a `Duration` field that is used to reserve the transmission channel to ensure that no collision will affect the acknowledgment frame. The `Sequence Control` field is mainly used by the receiver to remove duplicate frames. Duplicate frames are detected as follows. Each data frame contains a 12 bits sequence number in the `Sequence Control` field and the `Frame Control` field contains the `Retry` bit flag that is set when a frame is transmitted. Each 802.11 receiver stores the most recent sequence number received from each source address in frames whose `Retry` bit is reset. Upon reception of a frame with the `Retry` bit set, the receiver verifies its sequence number to determine whether it is a duplicated frame or not. 1211/10000 · 1211
44 ../../protocols/wifi.rst:115

	English IEEE 802.11 ACK and CTS frames 30/10000 · 30
45 ../../protocols/wifi.rst:120

	English 802.11 RTS/CTS frames are used to reserve the transmission channel, in order to transmit one data frame and its acknowledgment. The RTS frames contain a `Duration` and the transmitter and receiver addresses. The `Duration` field of the RTS frame indicates the duration of the entire reservation (i.e. the time required to transmit the CTS, the data frame, the acknowledgments and the required SIFS delays). The CTS frame has the same format as the acknowledgment frame. 469/10000 · 469
46 ../../protocols/wifi.rst:126

	English IEEE 802.11 RTS frame format 28/10000 · 28
47 ../../protocols/wifi.rst:129

	English The 802.11 service 18/10000 · 18
48 ../../protocols/wifi.rst:131

	English Despite the utilization of acknowledgments, the 802.11 layer only provides an unreliable connectionless service like Ethernet networks that do not use acknowledgments. The 802.11 acknowledgments are used to minimize the probability of frame duplication. They do not guarantee that all frames will be correctly received by their recipients. Like Ethernet, 802.11 networks provide a high probability of successful delivery of the frames, not a guarantee. Furthermore, it should be noted that 802.11 networks do not use acknowledgments for multicast and broadcast frames. This implies that in practice such frames are more likely to suffer from transmission errors than unicast frames. 682/10000 · 682
49 ../../protocols/wifi.rst:135

	English In addition to the data and control frames that we have briefly described above, 802.11 networks use several types of management frames. These management frames are used for various purposes. We briefly describe some of these frames below. A detailed discussion may be found in [IEEE802.11]_ and [Gast2002]_. 308/10000 · 308
50 ../../protocols/wifi.rst:141

	English A first type of management frames are the `beacon` frames. These frames are broadcasted regularly by access points. Each `beacon frame` contains information about the capabilities of the access point (e.g. the supported 802.11 transmission rates) and a `Service Set Identity` (SSID). The SSID is a null-terminated ASCII string that can contain up to 32 characters. An access point may support several SSIDs and announce them in beacon frames. An access point may also choose to remain silent and not advertise beacon frames. In this case, WiFi stations may send `Probe request` frames to force the available access points to return a `Probe response` frame. 657/10000 · 657
51 ../../protocols/wifi.rst:144

	English IP over 802.11 14/10000 · 14
52 ../../protocols/wifi.rst:146

	English Two types of encapsulation schemes were defined to support IP in Ethernet networks : the original encapsulation scheme, built above the Ethernet DIX format is defined in :rfc:`894` and a second encapsulation :rfc:`1042` scheme, built above the LLC/SNAP protocol [IEEE802.2]_. In 802.11 networks, the situation is simpler and only the :rfc:`1042` encapsulation is used. In practice, this encapsulation adds 6 bytes to the 802.11 header. The first four bytes correspond to the LLC/SNAP header. They are followed by the two bytes Ethernet Type field (`0x800` for IP and `0x806` for ARP). The figure below shows an IP packet encapsulated in an 802.11 frame. 653/10000 · 653
53 ../../protocols/wifi.rst:152

	English IP over IEEE 802.11 19/10000 · 19
54 ../../protocols/wifi.rst:154

	English The second important utilization of the management frames is to allow a WiFi station to be associated with an access point. When a WiFi station starts, it listens to beacon frames to find the available SSIDs. To be allowed to send and receive frames via an access point, a WiFi station must be associated to this access point. If the access point does not use any security mechanism to secure the wireless transmission, the WiFi station simply sends an `Association request` frame to its preferred access point (usually the access point that it receives with the strongest radio signal). This frame contains some parameters chosen by the WiFi station and the SSID that it requests to join. The access point replies with an `Association response frame` if it accepts the WiFI station. 783/10000 · 783
55 ../../protocols/wifi.rst:157

	English Footnotes 9/10000 · 9
56 ../../protocols/wifi.rst:158

	English The 802.11 working group defined the `basic service set (BSS)` as a group of devices that communicate with each other. We continue to use `network` when referring to a set of devices that communicate. 200/10000 · 200
57 ../../protocols/wifi.rst:160

	English In fact, the [IEEE802.11]_ frame format contains a fourth optional address field. This fourth address is only used when an 802.11 wireless network is used to interconnect bridges attached to two classical LAN networks. 218/10000 · 218
The translation has come to an end.

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the previous translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.