Source string Source string

640/10000 · 640
English Actions
This is an unpolished draft of the third edition of this e-book. If you find any error or have suggestions to improve the text, please create an issue via https://github.com/CNP3/ebook/issues?milestone=4 or help us by providing pull requests to close the existing issues.
Sharing resources
A network is designed to support a potentially large number of users that exchange information with each other. These users produce and consume information which is exchanged through the network. To support its users, a network uses several types of resources. It is important to keep in mind the different resources that are shared inside the network.
The first and more important resource inside a network is the link bandwidth. There are two situations where link bandwidth needs to be shared between different users. The first situation is when several hosts are attached to the same physical link. This situation mainly occurs in Local Area Networks (LAN). A LAN is a network that efficiently interconnects several hosts (usually a few dozens to a few hundreds) in the same room, building or campus. Consider for example a network with five hosts. Any of these hosts needs to be able to exchange information with any of the other hosts. A first organization for this LAN is the full-mesh.
The full-mesh is the most reliable and highest performing network to interconnect these five hosts. However, this network organization has two important drawbacks. First, if a network contains `n` hosts, then :math:`\frac{n\times(n-1)}{2}` links are required. If the network contains more than a few hosts, it becomes impossible to lay down the required physical links. Second, if the network contains `n` hosts, then each host must have :math:`n-1` interfaces to terminate :math:`n-1` links. This is beyond the capabilities of most hosts. Furthermore, if a new host is added to the network, new links have to be laid down and one interface has to be added to each participating host. However, full-mesh has the advantage of providing the lowest delay between the hosts and the best resiliency against link failures. In practice, full-mesh networks are rarely used except when there are few network nodes and resiliency is key.
The second possible physical organization, which is also used inside computers to connect different extension cards, is the bus. In a bus network, all hosts are attached to a shared medium, usually a cable through a single interface. When one host sends an electrical signal on the bus, the signal is received by all hosts attached to the bus. A drawback of bus-based networks is that if the bus is physically cut, then the network is split into two isolated networks. For this reason, bus-based networks are sometimes considered to be difficult to operate and maintain, especially when the cable is long and there are many places where it can break. Such a bus-based topology was used in early Ethernet networks.
A third organization of a computer network is a star topology. In such networks, hosts have a single physical interface and there is one physical link between each host and the center of the star. The node at the center of the star can be either a piece of equipment that amplifies an electrical signal, or an active device, such as a piece of equipment that understands the format of the messages exchanged through the network. Of course, the failure of the central node implies the failure of the network. However, if one physical link fails (e.g. because the cable has been cut), then only one node is disconnected from the network. In practice, star-shaped networks are easier to operate and maintain than bus-shaped networks. Many network administrators also appreciate the fact that they can control the network from a central point. Administered from a Web interface, or through a console-like connection, the center of the star is a useful point of control (enabling or disabling devices) and an excellent observation point (usage statistics).
A fourth physical organization of a network is the ring topology. Like the bus organization, each host has a single physical interface connecting it to the ring. Any signal sent by a host on the ring will be received by all hosts attached to the ring. From a redundancy point of view, a single ring is not the best solution, as the signal only travels in one direction on the ring; thus if one of the links composing the ring is cut, the entire network fails. In practice, such rings have been used in local area networks, but are now often replaced by star-shaped networks. In metropolitan networks, rings are often used to interconnect multiple locations. In this case, two parallel links, composed of different cables, are often used for redundancy. With such a dual ring, when one ring fails all the traffic can be quickly switched to the other ring.
A fifth physical organization of a network is the tree. Such networks are typically used when a large number of customers must be connected in a very cost-effective manner. Cable TV networks are often organized as trees.
Sharing bandwidth
In all these networks, except the full-mesh, the link bandwidth is shared among all connected hosts. Various algorithms have been proposed and are used to efficiently share the access to this resource. We explain several of them in the Medium Access Control section below.
Fairness in computer networks
Sharing resources is important to ensure that the network efficiently serves its user. In practice, there are many ways to share resources. Some resource sharing schemes consider that some users are more important than others and should obtain more resources. For example, on the roads, police cars and ambulances have priority. In some cities, traffic lanes are reserved for buses to promote public services, ... In computer networks, the same problem arise. Given that resources are limited, the network needs to enable users to efficiently share them. Before designing an efficient resource sharing scheme, one needs to first formalize its objectives. In computer networks, the most popular objective for resource sharing schemes is that they must be `fair`. In a simple situation, for example two hosts using a shared 2 Mbps link, the sharing scheme should allocate the same bandwidth to each user, in this case 1 Mbps. However, in a large networks, simply dividing the available resources by the number of users is not sufficient. Consider the network shown in the figure below where `A1` sends data to `A2`, `B1` to `B2`, ... In this network, how should we divide the bandwidth among the different flows ? A first approach would be to allocate the same bandwidth to each flow. In this case, each flow would obtain 5 Mbps and the link between `R2` and `R3` would not be fully loaded. Another approach would be to allocate 10 Mbps to `A1-A2`, 20 Mbps to `C1-C2` and nothing to `B1-B2`. This is clearly unfair.
In large networks, fairness is always a compromise. The most widely used definition of fairness is the `max-min fairness`. A bandwidth allocation in a network is said to be `max-min fair` if it is such that it is impossible to allocate more bandwidth to one of the flows without reducing the bandwidth of a flow that already has a smaller allocation than the flow that we want to increase. If the network is completely known, it is possible to derive a `max-min fair` allocation as follows. Initially, all flows have a null bandwidth and they are placed in the candidate set. The bandwidth allocation of all flows in the candidate set is increased until one link becomes congested. At this point, the flows that use the congested link have reached their maximum allocation. They are removed from the candidate set and the process continues until the candidate set becomes empty.
In the above network, the allocation of all flows would grow until `A1-A2` and `B1-B2` reach 5 Mbps. At this point, link `R1-R2` becomes congested and these two flows have reached their maximum. The allocation for flow `C1-C2` can increase until reaching 15 Mbps. At this point, link `R2-R3` is congested. To increase the bandwidth allocated to `C1-C2`, one would need to reduce the allocation to flow `B1-B2`. Similarly, the only way to increase the allocation to flow `B1-B2` would require a decrease of the allocation to `A1-A2`.
Network congestion
Sharing bandwidth among the hosts directly attached to a link is not the only sharing problem that occurs in computer networks. To understand the general problem, let us consider a very simple network which contains only point-to-point links. This network contains three hosts and two routers. All the links inside the network have the same capacity. For example, let us assume that all links have a bandwidth of 1000 bits per second and that the hosts send packets containing exactly one thousand bits.
In the network above, consider the case where host `A` is transmitting packets to destination `C`. `A` can send one packet per second and its packets will be delivered to `C`. Now, let us explore what happens when host `B` also starts to transmit a packet. Node `R1` will receive two packets that must be forwarded to `R2`. Unfortunately, due to the limited bandwidth on the `R1-R2` link, only one of these two packets can be transmitted. The outcome of the second packet will depend on the available buffers on `R1`. If `R1` has one available buffer, it could store the packet that has not been transmitted on the `R1-R2` link until the link becomes available. If `R1` does not have available buffers, then the packet needs to be discarded.
Besides the link bandwidth, the buffers on the network nodes are the second type of resource that needs to be shared inside the network. The node buffers play an important role in the operation of the network because that can be used to absorb transient traffic peaks. Consider again the example above. Assume that on average host `A` and host `B` send a group of three packets every ten seconds. Their combined transmission rate (0.6 packets per second) is, on average, lower than the network capacity (1 packet per second). However, if they both start to transmit at the same time, node `R1` will have to absorb a burst of packets. This burst of packets is a small `network congestion`. We will say that a network is congested, when the sum of the traffic demand from the hosts is larger than the network capacity :math:`\sum{demand}>capacity`. This `network congestion` problem is one of the most difficult resource sharing problem in computer networks. `Congestion` occurs in almost all networks. Minimizing the amount of congestion is a key objective for many network operators. In most cases, they will have to accept transient congestion, i.e. congestion lasting a few seconds or perhaps minutes, but will want to prevent congestion that lasts days or months. For this, they can rely on a wide range of solutions. We briefly present some of these in the paragraphs below.

Loading…

User avatar None

String updated in the repository

cnp3-ebook / principles/sharing — English

The first and more important resource inside a network is the link bandwidth. There are two situations where link bandwidth needs to be shared between different users. The first situation is when several hosts are attached to the same physical link. This situation mainly occurs in Local Area Networks (LAN). A LAN is a network that efficiently interconnects several hosts (usually a few dozens to a few hundreds) in the same room, building or campus. Consider for example a network with five hosts. Any of these hosts needs to be able to exchange information with any of the other hosts. A first organization for this LAN is the full-mesh.
The first and more important resource inside a network is the link bandwidth. There are two situations where link bandwidth needs to be shared between different users. The first situation is when several hosts are attached to the same physical link. This situation mainly occurs in Local Area Networks (LAN). A LAN is a network that efficiently interconnects several hosts (usually a few dozens to a few hundreds) in the same room, building or campus. Consider for example a network with five hosts. Any of these hosts needs to be able to exchange information with any of the other hosts. A first organization for this LAN is the full-mesh.
2 years ago
Browse all component changes

Glossary

English English
No related strings found in the glossary.

String information

Flags
read-only
Source string location
../../principles/sharing.rst:18
String age
2 years ago
Source string age
2 years ago
Translation file
locale/pot/principles/sharing.pot, string 4