Exit Zen
179
../../principles/sharing.rst:809
English
AIMD controls congestion by adjusting the transmission rate of the sources in reaction to the current congestion level. If the network is not congested, the transmission rate increases. If congestion is detected, the transmission rate is multiplicatively decreased. In practice, directly adjusting the transmission rate can be difficult since it requires the utilization of fine grained timers. In reliable transport protocols, an alternative is to dynamically adjust the sending window. This is the solution chosen for protocols like TCP and SCTP that will be described in more details later. To understand how window-based protocols can adjust their transmission rate, let us consider the very simple scenario of a reliable transport protocol that uses `go-back-n`. Consider the very simple scenario shown in the figure below.
0/8280 · 828
181
../../principles/sharing.rst:830
English
Consider first a window of one segment. This segment takes 4 msec to reach host `D`. The destination replies with an acknowledgment and the next segment can be transmitted. With such a sending window, the transmission rate is roughly 250 segments per second or 250 Kbps. This is illustrated in the figure below where each square of the grid corresponds to one millisecond.
0/3720 · 372
182
../../principles/sharing.rst:878
English
Consider now a window of two segments. Host `A` can send two segments within 2 msec on its 1 Mbps link. If the first segment is sent at time :math:`t_{0}`, it reaches host `D` at :math:`t_{0}+4`. Host `D` replies with an acknowledgment that opens the sending window on host `A` and enables it to transmit a new segment. In the meantime, the second segment was buffered by router `R1`. It reaches host `D` at :math:`t_{0}+6` and an acknowledgment is returned. With a window of two segments, host `A` transmits at roughly 500 Kbps, i.e. the transmission rate of the bottleneck link.
0/5800 · 580
183
../../principles/sharing.rst:951
English
Our last example is a window of four segments. These segments are sent at :math:`t_{0}`, :math:`t_{0}+1`, :math:`t_{0}+2` and :math:`t_{0}+3`. The first segment reaches host `D` at :math:`t_{0}+4`. Host `D` replies to this segment by sending an acknowledgment that enables host `A` to transmit its fifth segment. This segment reaches router `R1` at :math:`t_{0}+5`. At that time, router `R1` is transmitting the third segment to router `R2` and the fourth segment is still in its buffers. At time :math:`t_{0}+6`, host `D` receives the second segment and returns the corresponding acknowledgment. This acknowledgment enables host `A` to send its sixth segment. This segment reaches router `R1` at roughly :math:`t_{0}+7`. At that time, the router starts to transmit the fourth segment to router `R2`. Since link `R1-R2` can only sustain 500 Kbps, packets will accumulate in the buffers of `R1`. On average, there will be two packets waiting in the buffers of `R1`. The presence of these two packets will induce an increase of the round-trip-time as measured by the transport protocol. While the first segment was acknowledged within 4 msec, the fifth segment (`data(4)`) that was transmitted at time :math:`t_{0}+4` is only acknowledged at time :math:`t_{0}+11`. On average, the sender transmits at 500 Kbps, but the utilization of a large window induces a longer delay through the network.
0/13900 · 1390
186
../../principles/sharing.rst:1041
English
A congestion control scheme for our simple transport protocol could be implemented as follows.
0/940 · 94
187
../../principles/sharing.rst:1060
English
In the above pseudocode, `cwin` contains the congestion window stored as a real number of segments. This congestion window is updated upon the arrival of each acknowledgment and when congestion is detected. For simplicity, we assume that `cwin` is stored as a floating point number but only full segments can be transmitted.
0/3240 · 324
188
../../principles/sharing.rst:1063
English
As an illustration, let us consider the network scenario above and assume that the router implements the DECBit binary feedback scheme [RJ1995]_. This scheme uses a form of Forward Explicit Congestion Notification and a router marks the congestion bit in arriving packets when its buffer contains one or more packets. In the figure below, we use a `*` to indicate a marked packet.
0/3800 · 380
189
../../principles/sharing.rst:1218
English
When the connection starts, its congestion window is set to one segment. Segment `S0` is sent an acknowledgment at roughly :math:`t_{0}+4`. The congestion window is increased by one segment and `S1` and `S2` are transmitted at time :math:`t_{0}+4` and :math:`t_{0}+5`. The corresponding acknowledgments are received at times :math:`t_{0}+8` and :math:`t_{0}+10`. Upon reception of this last acknowledgment, the congestion window reaches `3` and segments can be sent (`S4` and `S5`). When segment `S6` reaches router `R1`, its buffers already contain `S5`. The packet containing `S6` is thus marked to inform the sender of the congestion. Note that the sender will only notice the congestion once it receives the corresponding acknowledgment at :math:`t_{0}+18`. In the meantime, the congestion window continues to increase. At :math:`t_{0}+16`, upon reception of the acknowledgment for `S5`, it reaches `4`. When congestion is detected, the congestion window is decreased down to `2`. This explains the idle time between the reception of the acknowledgment for `S*6` and the transmission of `S10`.
0/10970 · 1097
190
../../principles/sharing.rst:1220
English
In practice, a router is connected to multiple input links. The figure below shows an example with two hosts.
0/1090 · 109
191
../../principles/sharing.rst:1279
English
In general, the links have a non-zero delay. This is illustrated in the figure below where a delay has been added on the link between `R` and `C`.
0/1460 · 146
192
../../principles/sharing.rst:1326
English
Footnotes
21/100 · 9
195
../../principles/sharing.rst:1331
English
Some networking technologies allow to adjust dynamically the bandwidth of links. For example, some devices can reduce their bandwidth to preserve energy. We ignore these technologies in this basic course and assume that all links used inside the network have a fixed bandwidth.
0/2770 · 277
196
../../principles/sharing.rst:1333
English
In this section, we focus on congestion control mechanisms that regulate the transmission rate of the hosts. Other types of mechanisms have been proposed in the literature. For example, `credit-based` flow-control has been proposed to avoid congestion in ATM networks [KR1995]_. With a credit-based mechanism, hosts can only send packets once they have received credits from the routers and the credits depend on the occupancy of the router's buffers.
0/4510 · 451
197
../../principles/sharing.rst:1335
English
For example, the measurements performed in the Sprint network in 2004 reported more than 10k active TCP connections on a link, see https://research.sprintlabs.com/packstat/packetoverview.php. More recent information about backbone links may be obtained from caida_ 's real-time measurements, see e.g. http://www.caida.org/data/realtime/passive/
0/3450 · 345
The translation has come to an end.